Visit The New, Modern Unix Linux Community


Change SCO - GUI or Desktop interface to DOS based interface


 
Thread Tools Search this Thread
Operating Systems SCO Change SCO - GUI or Desktop interface to DOS based interface
# 1  
Computer Change SCO - GUI or Desktop interface to DOS based interface

Hi all


I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?

If you have any ideas, please tell me then. Thank you
# 2  
There are 12 desktops available.
Press <ctrl><alt><F1> thru <F12> for each one. By default <F2> is the graphical interface, the other 11 are 80x25 text.
<F1> is the also the console, where system error messages may also be sent.
This User Gave Thanks to jgt For This Post:
# 3  
IIRC, the change from GUI to command line is handled by modification of /etc/init in the activation line for tty01.
Switching between the 12 ttys on the console keyboard is normally [ALT][Fkey] but getting out of the GUI on tty01 requires [CTRL][ALT][Fkey].
This User Gave Thanks to edfair For This Post:

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

Test Your Knowledge in Computers #154
Difficulty: Easy
Inspur K-UX is a Linux distribution certified as UNIX 03 compliant.
True or False?

9 More Discussions You Might Find Interesting

1. Linux

Possible to change the interface name in Linux based appliance?

the appliance is running on linux and accessible via http,telnet,etc. When I do start-shell, I can access to its filesystem. I am trying to change the interface name, currently is input1 to port-1. It is not possible to change in WebGui or its CLI. Possible to access its filesystem and change... (0 Replies)
Discussion started by: user51
0 Replies

2. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

3. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

4. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

5. IP Networking

Selecting Interface based on Destination IP address

Hi all, How an interface is selected based on the destination ip address. Thanks in advance........ (5 Replies)
Discussion started by: vijaypdp2006
5 Replies

6. Solaris

how to change the subnet mask of interface

Hi all, could you please tell me how to Change the subnet mask of interface aded:1 from ffffffc0 to ffffff80 regards Krishna (7 Replies)
Discussion started by: murthy76
7 Replies

7. Programming

How to modify this c code to get full GUI interface for Unix Linux ?

Hi, the following code comes from Unix Linux dialog utility project. Unfortunately, this project is no more actively maintained. Unix Linux dialog utility is made of widget boxes. One of them is mixedgauge.c In the following example I would like to get rid of flickering when run in... (0 Replies)
Discussion started by: jack2
0 Replies

8. UNIX for Advanced & Expert Users

Possible GUI to Command-Line Interface Translator?

I was chatting with my teacher on how this could be a great tool for admins who are making the switch from GUI to CLI administration. I'm wondering, does this kind of tool exist? (4 Replies)
Discussion started by: Daemon-Killer
4 Replies

9. SCO

sco GUI interface

Why can I not login to the SCO GUI interface login screen? (1 Reply)
Discussion started by: qphillips
1 Replies

Featured Tech Videos