Visit Our UNIX and Linux User Community


stage 1 boot failure: error loading hd (40)/boot


 
Thread Tools Search this Thread
Operating Systems SCO stage 1 boot failure: error loading hd (40)/boot
# 1  
Old 07-30-2010
stage 1 boot failure: error loading hd (40)/boot

hi

SCO Unix 5.0.6 doesn't boot due to this problem:
Code:
not a directory
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot

Knows someone howto solve it?
# 2  
Old 07-30-2010
If this message occurs while booting the native operating system then you have destroyed the active partition on the disk.
# 3  
Old 07-30-2010
The system was crashing completely and now it doesn't boot.

Is it any software to boot from CD to repair the MBR or Partition Table from SCO unix or howto read files from the SCO file system?
# 4  
Old 07-30-2010
The master boot block is probably intact, as the system knows which partition to try to boot.
I would get a new hard drive, install 5.0.6 on it, and then add the current drive as a second disk.
If this is a SCSI system don't forget to change the scsi id, and most scsi drives have a read only jumper, set it.
If it is an IDE system, then either make the drive a slave and add to the primary controller, or add to the secondary controller (depending where the CD drive is connected)
Use mkdev hd to add the drive, do NOT make any new filesystems when running divvy.
# 5  
Old 07-30-2010
Thx a lot,

Where can I download setup software of 5.0.6?

I cannot find a setup CD and cannot find under:

ftp://ftp.sco.com/pub/openserver5/

BTW is it any other way to read SCO file system instead of add the current drive as a second disk?
# 6  
Old 07-30-2010
Deeper doodoo.
The 5.0.6 Media kit is not available on SCO's web site.
Download the 5.0.7 CD, and install it. You can install it for a 30 day evaluation, then follow the instructions to add a second disk.
Once you have salvaged the data that you need from the old disk, you will have to decide what to do if you don't have a 5.0.6 media kit, and or license data.
5.0.7 includes the program 'cdrecord' which will allow you to create standard CD or DVD disks. You can write to dual layer DVD's (9.4GB) using an LG brand DVD writer that sells for about 25 dollars US.
# 7  
Old 07-31-2010
Thx, I've download OSR507V_hv_1.0.0Fe.iso, burned on CD, but the machine won't boot from this CD.
I cannot understand why, in the Bios Boot Order is CD on the top.

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. SCO

FATAL BOOT ERROR: Canít load stage 3

I'm under huge pressure to recover data from an old server that only gets booted very infrequently. The data on it is urgently required - isn't always??! .. Server is an HP DL380G5 which is running SCO Unixware 7.11 .. It has 3 partitions in a RAID 5 Configuration: 1 of 10GB (I assume it... (19 Replies)
Discussion started by: BernP
19 Replies

2. UNIX for Dummies Questions & Answers

boot up failure unix sco after power failure

hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies

3. Solaris

Failure to boot v445

Hi Guys, I have a small problem with a v445 which I have been informed will only boot with the reconfigure option enabled. It is attached to HP SAN storage using qla2300 FCA's with a Veritas encapsulated rootvoldg (No Laughing here please) when I try a reboot I get the following error. ... (5 Replies)
Discussion started by: gull04
5 Replies

4. Solaris

Loading Kernel module at boot

Is there any link/tutorial on loading Solaris kernel modules at boot time?? (0 Replies)
Discussion started by: unisolin
0 Replies

5. Solaris

Boot failure

I have installed Solaris 10 OS in Sun Virtual Box that uses x86 32 bit system. After an abnormal shutdown i'm getting the following message on the console when i try to boot. SunOS Release 5.10 Version Generic_127128_11 32-bit Copyright 1983-200 Sun Microsystems, Inc. All rights reserrved. Use... (3 Replies)
Discussion started by: Sesha
3 Replies

6. Solaris

INT18 boot failure

I installed solaris virtually and tried to format the partitions .. I dont know what went wrong, It got rebooted and hangs in the screen "No partitions" and after pressing Enter button it goes to "INT18 boot failure" and hangs there once again . Could any one of you suggest why this has happened... (3 Replies)
Discussion started by: priky
3 Replies

7. Linux

Boot failure

Hi all I used a dual boot operating system and it works fine for me. Now , i install a Ati radeon 9250 Agp card on my system and this results in boot failure of fedora 6. The graphics card is working fine with windows XP , i.e i have no compatibility issues.The system also refuses to boot when i... (2 Replies)
Discussion started by: joshighanshyam
2 Replies

8. Solaris

Solaris 10 - boot CD not loading

I recently downloaded solaris 10 disk images and I am trying to load it onto my system. I cannot get the PC to load off of the disk 1 image. I created the disk using windows easy cd creator just like the download instructions said, but i get a boot failure. :eek: Any ideas??? ( BIOS ok !!! ) ... (10 Replies)
Discussion started by: spider123
10 Replies

9. Solaris

solaris boot problem boot error loading interpreter(misc/krtld)

When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error. cannot find mis/krtld boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies

10. UNIX for Dummies Questions & Answers

Loading windows on a dual boot

I want to dual-boot Windows 98 and Redhat 7. My scheme for doing this is to partition into: A FAT32 partition for windows A Linux partition for root A swap partition A boot partition My question is: At what point do I setup windows on the FAT partition? Would I do it from the command line... (5 Replies)
Discussion started by: Furtoes00
5 Replies

Featured Tech Videos