10 More Discussions You Might Find Interesting
1. BSD
I put this thread to shell and bsd, because I want to resolve this matter on bsd.
May somebody can explain to me how to ping a remote server, in unix. BTW the following code examples were tried on a linux system as well, with the same output, nothing. But on my bsd are not installed nmap neither... (4 Replies)
Discussion started by: 1in10
4 Replies
2. Shell Programming and Scripting
Hello,
I need help, I have the following which save in the result file ping and telnet:port test.
Basically the script works but I should implement a check on ping and telnet command so that ping has 5 seconds threshold and telnet (more important) 10 seconds. Over that threshold ping and... (0 Replies)
Discussion started by: marmellata
0 Replies
3. AIX
Hi,
After a crash of our older AIX server it happend as it is in the title:
ping is ok, but telnet:
What it can be this strange thing?
Franci (2 Replies)
Discussion started by: frajer
2 Replies
4. UNIX for Advanced & Expert Users
Hi all,
I am not sure if my problem is specific to HP-UX or not. Hopefully someone can tell me what's wrong.
I have a server name server1 10.100.50.10 in the /etc/hosts file and if I do a ping server1, it shows the right IP address.
However, if I run telnet server1, it is not using... (4 Replies)
Discussion started by: newbie_01
4 Replies
5. Infrastructure Monitoring
We have a Sun Solaris Netra 20 server. Our O&M Server gets Alarm Processor
not responding. When Alarm occurs, you can ping the sun server but cannot telnet it. We keep getting Interrupt level not serviced. var/adm/message log is
> tail -f messages
Apr 12 20:09:56 cama pcisch: PCI-device:... (9 Replies)
Discussion started by: krabu
9 Replies
6. IP Networking
I have one problem and it is giving me hard time
I can ping my windows machine
root@x1ChXpress:/sbin
>ping 192.168.129.66
192.168.129.66 is alive
root@x1ChXpress:/sbin
>netstat -rn
Routing Table:
Destination Gateway Flags Ref Use Interface... (3 Replies)
Discussion started by: amon
3 Replies
7. AIX
Hi All,
We are not able to ping to a AIX box...Network is ok..when we give ping from that AIX box..it is giving 0821-067 ping: The socket creation call failed.there is no enough buffer space for the requested socket operation.
refresh -s inetd is also giving socket error.
Please help to... (1 Reply)
Discussion started by: b_manu78
1 Replies
8. UNIX for Dummies Questions & Answers
Hi guys,
Please bear with me
i have a sco 5.0.6 openserver i'm telnet in to it. (via dsl)
After 7 minutes it will kick me out of my program.
Is there any settings that i need to change in order to stop the time out problem.
I dont have any router or hub (dsl modem to nic card )
Also... (6 Replies)
Discussion started by: josramon
6 Replies
9. UNIX for Advanced & Expert Users
I was wondering if anyone knew how I would open up my server so it can be telneted into from other subnets.:confused: (2 Replies)
Discussion started by: cparks73
2 Replies
10. IP Networking
I can ping other computers in my office. I can telnet other users in my office but i cannot get out of the office network. If i try to go out side of my network it cannot find host.
Any ideas? (5 Replies)
Discussion started by: macdonto
5 Replies
DNPING(1) General Commands Manual DNPING(1)
NAME
dnping - Loopbacks diagnostic packets through a remote node
SYNOPSIS
dnping nodename [user pass] count
or
dnping nodename [options] nodename
Options:
[qsv] [-c number] [-i interval] [-p password] [-s size] [-u username] [-w timeout]
DESCRIPTION
This utility sends to remote DECnet node nodename the number of packets specified by count to test the link between the two systems.
Optionally a username and password may be specified for the connection as well as several other options. NOTE that if you dnping another
Linux box it must have dnetd running.
NOTE also that dnping is not really like an IP "ping" in that it needs a registered object at the other end to connect to. So, just because
you cannot ping a machine does not, necessarily, mean that machine is not available, just that the MIRROR object is not available. There is
not (to my knowledge) a low-level equivalent in DECnet of the ICMP ping message.
OPTIONS
-c number
Number of packets to send (default 10)
-d Debug mode (default off)
-i interval
interval between packets in microseconds (default 0)
-p password
Access control password. If this is "-" then you will be prompted.
-q Quiet mode (default off)
-s size
size of frame to send in bytes (40 data + 68 hdr)
-t timestamps mode (default off)
-u username
access control username
-w timeout
Specifies a timeout (in seconds). If not response is received after this time then dnping will abort. The default is to wait for-
ever.
-v verbose mode (default off)
EXAMPLES
Pings 10 packets through remote node "mv3100"
# dnping mv3100 10
Make it look a bit like IP ping:
# dnping -vti 1000000 marsha
SEE ALSO
dntype(1), dndir(1), dndel(1), dntask(1), sethost(1), dnetd(8)
DECnet utilities January 25 2000 DNPING(1)