Boot Issues


 
Thread Tools Search this Thread
Operating Systems Linux Red Hat Boot Issues
# 1  
Old 09-13-2018
Boot Issues

I am installing Red Hat Linux 6.9 as a VM in Hyper-V on an HP laptop running Windows 10. After the install completes and the VM reboots, it gives me the message, "Detected CPU Family 6 model 142; Warning: Intel CPU model - this hardware has not undergone testing by Red Hat and might not be certified" (see screenshot). I also got this message when installing Red Hat Linux 6.7, but Linux booted up fine after getting that message. Now, with 6.9, after I get that message, I get a black screen with a funny looking bar across the top of it and then it just hangs (see screenshot). Anyone else experienced this issue or does anyone have any suggestions?
# 2  
Old 02-16-2019
Sounds like it is more of a Hyper-V problem than a Red-Hat issue.
It may well be that Hyper-V didn't support newer technology that
Red-Hat may have implemented at the time.


When running any guest OS through a hypervisor, you should try
the hypervisor forums first. This isn't a Windows 10 forum.
Login or Register to Ask a Question

Previous Thread | Next Thread

7 More Discussions You Might Find Interesting

1. Solaris

WAN boot Server issues.

I 'm trying to configure a WAN boot server on Solaris10 x86 for sparc clients .. when i try to set up the server m getting following error ./setup_install_server -w /var/apache2/htdocs/wanboot10/wpath /var/apache2/htdocs/wanboot10/ipath ERROR: Cannot make WAN boot Image file on this... (6 Replies)
Discussion started by: fugitive
6 Replies

2. Solaris

Boot issues Solaris 10 + V440

Hello, I've a very weird problem with one of the machines. When I try to boot off a working DVD that I used to install another system with it spits out the following message: Sun Fire V440, No Keyboard Copyright 2007 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.22.33, 8192 MB... (14 Replies)
Discussion started by: stoci
14 Replies

3. Solaris

Windows,Solaris, Red Hat triple boot issues

I have a pentium IV with 512 MB ram and 80 GB HDD. I first installed windows XP on the first primary partition, then Solaris on the second with 20 GB for the solaris partition, and when rebooted , the grub menu functioned as expected giving me the options to dual boot, so next I wanted to install... (3 Replies)
Discussion started by: saagar
3 Replies

4. SCO

xp/sco 5.0.7 dual boot issues

Hello those more knowledgeable than I: I have been trying to get xp and SCO to coexist on the same system. I have tried several different ways to make both work, here's the list: -install xp, image it, move the partition to the end of drive, verify it boots, image again, -boot off of SCO... (6 Replies)
Discussion started by: stay0ut
6 Replies

5. Solaris

V1280 boot issues

I have a client with a V1280 onsite and it is having boot problems. Below is the message it is returning when trying to boot. Is this something that anybody has run into, or that you might be able to shed some light on? {0} ok boot /ssm@0,0/pci@18,700000/ide@3/cdrom@0,0:f SunOS Release 5.9... (3 Replies)
Discussion started by: xcwhitex
3 Replies

6. UNIX for Advanced & Expert Users

boot issues...

hardware on my first FreeBSD server has crashed. i was planning on swapping the HD into another machine, booting the generic kernel and then custom tailoring it to the new machine specs. however, i'm having a problem. the new machine is using a promise ultra100 card. i don't have any... (2 Replies)
Discussion started by: xyyz
2 Replies

7. UNIX for Advanced & Expert Users

Solaris boot issues

i'm having 2 problems. 1. the system will always look to boot from the net. i've changed the prom settings so that it boots from the disk, by entering "setenv boot-device disk0:3", but the system still seems to want to boot from the net. 2. i replaced my creator3d with an elitem6 and i did... (6 Replies)
Discussion started by: xyyz
6 Replies
Login or Register to Ask a Question