We have a network of Lucent BSTDX9000 switches for fiber and wireless links in the United States and Costa Rica. I was dragging a BSTDX9000 icon in my Naviscore NMS and it disappeared.
All of my trunks are still up but I can't figure out how to get the icon back. I'm screwed if something happens in that switch and I can't get into it.
If you or somebody you know can help, it would be greatly appreciated
I'm willing to pay whatever it takes and we can set someone up to remotely log in.
You can also contact me on my cell. 602-370-9750
Hi,
I am using
SUSE Linux Enterprise Server 11 (x86_64), PATCHLEVEL = 0 as NIS server.
All client is having SUSE Linux Enterprise Desktop 11 (x86_64), PATCHLEVEL = 0.
All system are configured to work in GUI.
When NIS user say 'a' locks system, and user 'b' wants to login to the same system... (1 Reply)
hi,
how to access console of a switch having rj45 on switch side to db 9 female on pc side console cable which needs to be connected to one console server having rj11 on its side and db 9 female on other end.i.e. on switch side,console cable has rj45 and db 9 pin female connector on other side of... (1 Reply)
Guys,
I need to copy files from source to destination with datetime preserved
I did it with cp -p <source>/file <destinaltion>/file
But when I do stat command on copied file , it seems the copied file has "change time" modified.
Please guide me in understanding (2 Replies)
We have a network of Lucent BSTDX9000 switches for fiber and wireless links in the United States and Costa Rica. I was dragging a BSTDX9000 switch icon in my Naviscore NMS and it disappeared.
All of my trunks and circuits are still fuctioning properly but I can't figure out how to get the icon... (3 Replies)
Hello there,
I wanted to know the members' opinion about the best open source network management software which uses a web browser to show its interface and results.
I am interested in the software for both windows and Linux OSs.
Thanks. (4 Replies)
Im running mandrake 9.0 and i just got a Lucent/orinoco PC24E-H-FC. I beleive it was originaly made by lucent but then made by Orinoco.. But anyways i just cant get connected. Ive tried 3 differemt drivers. My wireless access point router is a Linksys. I just cant figure this out ive talked on... (3 Replies)
hi,
i am try to run following script in c-shell, using switch command.
#!/bin/csh
choice=0
while
do
echo "system monitor"
echo "
1) system paging
2) system file inf.
3) system disk inf.
9) exit
"
echo "select an option: \c"
read choice
case $choice in
1)... (3 Replies)
WAVELAN_CS(4) Kernel Interfaces Manual WAVELAN_CS(4)NAME
wavelan_cs - AT&T GIS WaveLAN PCMCIA device driver
SYNOPSIS
insmod wavelan_cs.o [irq_list=i,j,...] [mem_speed=n] [do_roaming=n]
DESCRIPTION
wavelan_cs is the low-level Card Services driver for the NCR / AT&T / Lucent WaveLAN PCMCIA and Digital (DEC) RoamAbout DS wireless ether-
net adapter. When this driver is attached to a card, it allocates the next available ethernet device (eth0..eth#). This device name will
be passed on to cardmgr(8) for the card configuration, and reported in the kernel log file with the MAC address, NWID and frequency used by
the card.
PARAMETERS
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
mem_speed=n
Sets the access speed of the shared memory window, in nanoseconds. The default is 0 (i.e., no extra wait states).
do_roaming=n
Enables or disables roaming mode. The default is 1 (roam).
WIRELESS EXTENSIONS
Use iwconfig(8) to manipulate wireless extensions.
Mode
Set the operating mode to Ad-Hoc or Managed. This in fact disable or enable roaming support. This setting is not saved in hardware.
Network ID
Set the network ID [0 to FFFF] or disable it [off] or reenable it [on]. As the NWID is stored in the card Permanent Storage Area, it will
be reuse at any further invocation of the driver.
Frequency & channels
For the 2.4GHz 2.00 Hardware, you are able to set the frequency by specifying one of the 10 defined channels (2.412, 2.422, 2.425, 2.4305,
2.432, 2.442, 2.452, 2.460, 2.462 or 2.484) or directly by its value. The frequency is changed immediately and permanentely. Frequency
availability depend on the regulations...
Sensitivity
Signal level threshold for packet reception [0 to 63]. Should be set according to the ambiant noise level.
Encryption key
Set the encryption key [0 to FFFF-FFFF-FFFF-FFFF]. Use [off] and [on] to disable and reenable the hardware encryption. This feature works
only for device with encryption option (DES or AES).
Statistics spy
Set a list of MAC addresses in the driver (up to 8) and get the last quality of link for each of those (see iwspy(8)).
/proc/net/wireless
status is the status reported by the modem. Link quality reports the quality of the modulation on the air (direct sequence spread spec-
trum) [max = 16]. Level and Noise refer to the signal level and noise level [max = 64]. The crypt discarded packet and misc discarded
packet counters are not implemented.
PRIVATE IOCTL
You may use iwpriv(8) to manipulate private ioctls.
Quality threshold
Enable you the define the quality threshold used by the modem (packet below that level are discarded).
Histogram
This functionality allow to set a number of signal level intervals and to count the number of packets received in each of those defined
intervals. This distribution might be used to calculate the mean value and standard deviation of the signal level.
OTHER FEATURES
Hot unplug support.
Power saving (use 'ifconfig down').
SPECIFIC NOTES
This driver will fail to load some non NCR/ATT&T/Lucent Wavelan cards. If it's your case, you must look in the source code on how to add
your card to the detection routine.
Some of the mentioned features are optional. You may enable to disable them by changing flags in the driver header and recompile.
AUTHOR
Anthony D. Joseph - adj@lcs.mit.edu
Jean Tourrilhes - jt@hplb.hpl.hp.com
(+ others - see source code for details)
SEE ALSO wavelan(4), cardmgr(8), pcmcia(5), ifconfig(8), insmod(1), iwconfig(8), iwspy(8), iwpriv(8).
MIT Lab. for Comp. Sci. 4/16/95 WAVELAN_CS(4)
