Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

siis(4) [v7 man page]

SIIS(4) 						   BSD Kernel Interfaces Manual 						   SIIS(4)

NAME
siis -- SiliconImage Serial ATA Host Controller driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device pci device scbus device siis Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): siis_load="YES" The following tunables are settable from the loader(8): hint.siis.X.msi controls Message Signaled Interrupts (MSI) usage by the specified controller. hint.siisch.X.pm_level controls SATA interface Power Management for the specified channel, allowing some power to be saved at the cost of additional command latency. Possible values: 0 interface Power Management is disabled (default); 1 device is allowed to initiate PM state change, host is passive. Note that interface Power Management is not compatible with device presence detection. A manual bus reset is needed on device hot-plug. hint.siisch.X.sata_rev setting to nonzero value limits maximum SATA revision (speed). Values 1, 2 and 3 are respectively 1.5, 3 and 6Gbps. DESCRIPTION
This driver provides the CAM(4) subsystem with native access to the SATA ports of controller. Each SATA port is represented to CAM as a sep- arate bus with 16 targets. Most of the bus-management details are handled by the SATA-specific transport of CAM. Connected ATA disks are handled by the ATA protocol disk peripheral driver ada(4). ATAPI devices are handled by the SCSI protocol peripheral drivers cd(4), da(4), sa(4), etc. Driver features include support for Serial ATA and ATAPI devices, Port Multipliers (including FIS-based switching), hardware command queues (31 command per port), Native Command Queuing, SATA interface Power Management, device hot-plug and Message Signaled Interrupts. Same hardware is also supported by the atasiliconimage driver from ata(4) subsystem. If both drivers are loaded at the same time, this one will be given precedence as the more functional of the two. HARDWARE
The siis driver supports the following controllers: o SiI3124 o SiI3132 o SiI3531 SEE ALSO
ada(4), ata(4), cam(4), cd(4), da(4), sa(4) HISTORY
The siis driver first appeared in FreeBSD 8.0. AUTHORS
Alexander Motin <mav@FreeBSD.org>. BSD
July 18, 2009 BSD

Check Out this Related Man Page

SIIS(4) 						   BSD Kernel Interfaces Manual 						   SIIS(4)

NAME
siis -- SiliconImage Serial ATA Host Controller driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device pci device scbus device siis Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): siis_load="YES" The following tunables are settable from the loader(8): hint.siis.X.msi controls Message Signaled Interrupts (MSI) usage by the specified controller. hint.siisch.X.pm_level controls SATA interface Power Management for the specified channel, allowing some power to be saved at the cost of additional command latency. Possible values: 0 interface Power Management is disabled (default); 1 device is allowed to initiate PM state change, host is passive. Note that interface Power Management is not compatible with device presence detection. A manual bus reset is needed on device hot-plug. hint.siisch.X.sata_rev setting to nonzero value limits maximum SATA revision (speed). Values 1, 2 and 3 are respectively 1.5, 3 and 6Gbps. DESCRIPTION
This driver provides the CAM(4) subsystem with native access to the SATA ports of controller. Each SATA port is represented to CAM as a sep- arate bus with 16 targets. Most of the bus-management details are handled by the SATA-specific transport of CAM. Connected ATA disks are handled by the ATA protocol disk peripheral driver ada(4). ATAPI devices are handled by the SCSI protocol peripheral drivers cd(4), da(4), sa(4), etc. Driver features include support for Serial ATA and ATAPI devices, Port Multipliers (including FIS-based switching), hardware command queues (31 command per port), Native Command Queuing, SATA interface Power Management, device hot-plug and Message Signaled Interrupts. Same hardware is also supported by the atasiliconimage driver from ata(4) subsystem. If both drivers are loaded at the same time, this one will be given precedence as the more functional of the two. HARDWARE
The siis driver supports the following controllers: o SiI3124 o SiI3132 o SiI3531 SEE ALSO
ada(4), ata(4), cam(4), cd(4), da(4), sa(4) HISTORY
The siis driver first appeared in FreeBSD 8.0. AUTHORS
Alexander Motin <mav@FreeBSD.org>. BSD
July 18, 2009 BSD
Man Page