Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

reboot(8) [ultrix man page]

reboot(8)						      System Manager's Manual							 reboot(8)

Name
       reboot - automatic reboot procedures

Syntax
       /etc/reboot [ -n ] [ -q ]

Description
       The  ULTRIX  system is booted by loading a kernel image, usually into memory at location zero and transferring to zero.	Because the system
       is not reenterable, the kernel image must be read in from disk each time the system is bootstrapped.

       When the reboot of a running system is desired, is normally used.  If there are no users, can be used.  The command causes the disks to	be
       synced,	and  then  a multiuser reboot is initiated.  The system is booted and an automatic disk check is performed.  If the procedure suc-
       ceeds, the system is then brought up for the users.

       The system will reboot itself after a power failure or after a crash, provided auto-restart is enabled on your system.  A consistency check
       of the file systems will be performed and, unless the check fails, the system will resume multiuser operations.

Options
       -n   Prevents the disks from being synced.

       -q   Reboots quickly and ungracefully, without shutting down running processes first.

Files
       System code

See Also
       crash(8v), fsck(8), halt(8), init(8), newfs(8), rc(8), shutdown(8)

																	 reboot(8)

Check Out this Related Man Page

REBOOT(8)						      System Manager's Manual							 REBOOT(8)

NAME
reboot - stopping and restarting the system SYNOPSIS
/sbin/reboot [ -lqnhdarsfRD ] /sbin/halt [ -lqndars ] /sbin/fastboot [ -lqndarsRD ] DESCRIPTION
2.11BSD is started by placing it in memory at location zero and transferring to its entry point. Since the system is not reentrant, it is necessary to read it in from disk or tape each time it is to be boot strapped. Rebooting a running system: When the system is running and a reboot is desired, shutdown(8) is normally used to stop time sharing and put the system into single user mode. If there are no users then /sbin/reboot can be used without shutting the system down first. Reboot normally causes the disks to be synced and allows the system to perform other shutdown activities such as resynchronizing hardware time-of-day clocks. A multi-user reboot (as described below) is then initiated. This causes a system to be booted and an automatic disk check to be performed. If all this succeeds without incident, the system is then brought up for multi-user operation. Options to reboot are: -l Don't try to tell syslogd(8) what's about to happen. -q Reboot quickly and ungracefully, without shutting down running processes first. -n Don't sync before rebooting. This can be used if a disk or the processor is on fire. -h Don't reboot, simply halt the processor. -d Dump memory onto the dump device, usually part of swap, before rebooting. The dump is done in the same way as after a panic. -a Have the system booter ask for the name of the system to be booted, rather than immediately booting the default system (/unix). -r Mount the root file system as read only when the system reboots. This is not supported by the kernel in 2.11BSD. -s Don't enter multi-user mode after system has rebooted - stay in single user mode. -f Fast reboot. Omit the automatic file system consistency check when the system reboots and goes multi-user. This is accomplished by passing a fast reboot flag on to the rebooting kernel. This currently prevents the use of -f flag in conjunction with the -h (halt) flag. -D Set the autoconfig(8) debug flag. This is normally not used unless one is debugging the autoconfig program. -R Tells the kernel to use the compiled in root device. Normally the system uses the device from which it was booted as the root/swap/pipe/dump device. Reboot normally places a shutdown record in the login accounting file /usr/adm/wtmp. This is inhibited if the -q or -n options are present. Note that the -f (fast reboot) and -n (don't sync) options are contradictory; the request for a fast reboot is ignored in this case. Halt and fastboot are synonymous with ``reboot -h'' and ``reboot -f'', respectively. Power fail and crash recovery: Normally, the system will reboot itself at power-up or after crashes if the contents of low memory are intact. An automatic consistency check of the file systems will be performed, and unless this fails, the system will resume multi-user operations. SEE ALSO
autoconfig(8), sync(2), utmp(8), shutdown(8), syslogd(8) 3rd Berkeley Distribution May 24, 1996 REBOOT(8)
Man Page