Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

cat(1) [ultrix man page]

cat(1)							      General Commands Manual							    cat(1)

Name
       cat - concatenate and print data

Syntax
       cat [ -b ] [ -e ] [ -n ] [ -s ] [ -t ] [ -u ] [ -v ] file...

Description
       The  command reads each file in sequence and displays it on the standard output.  Therefore, to display the file on the standard output you
       type:
       cat file
       To concatenate two files and place the result on the third you type:
       cat file1 file2 > file3
       To concatenate two files and append them to a third you type:
       cat file1 file2 >> file3
       If no input file is given, or if a minus sign (-) is encountered as an argument, reads from the standard input file.  Output is buffered in
       1024-byte blocks unless the standard output is a terminal, in which case it is line buffered.  The utility supports the processing of 8-bit
       characters.

Options
       -b   Ignores blank lines and precedes each output line with its line number.

       -e   Displays a dollar sign ($) at the end of each output line.

       -n   Precedes all output lines (including blank lines) with line numbers.

       -s   Squeezes adjacent blank lines from output and single spaces output.

       -t   Displays non-printing characters (including tabs) in output.  In addition to those representations used with the -v  option,  all  tab
	    characters are displayed as ^I.

       -u   Unbuffers output.

       -v   Displays  non-printing  characters (excluding tabs and newline) as the ^x.	If the character is in the range octal 0177 to octal 0241,
	    it is displayed as M-x. The delete character (octal 0177) displays as ^?.  For example, is displayed as ^X.

See Also
       cp(1), ex(1), more(1), pr(1), tail(1)

																	    cat(1)

Check Out this Related Man Page

CAT(1)							    BSD General Commands Manual 						    CAT(1)

NAME
cat -- concatenate and print files SYNOPSIS
cat [-benstuv] [file ...] DESCRIPTION
The cat utility reads files sequentially, writing them to the standard output. The file operands are processed in command-line order. If file is a single dash ('-') or absent, cat reads from the standard input. If file is a UNIX domain socket, cat connects to it and then reads it until EOF. This complements the UNIX domain binding capability available in inetd(8). The options are as follows: -b Number the non-blank output lines, starting at 1. -e Display non-printing characters (see the -v option), and display a dollar sign ('$') at the end of each line. -n Number the output lines, starting at 1. -s Squeeze multiple adjacent empty lines, causing the output to be single spaced. -t Display non-printing characters (see the -v option), and display tab characters as '^I'. -u Disable output buffering. -v Display non-printing characters so they are visible. Control characters print as '^X' for control-X; the delete character (octal 0177) prints as '^?'. Non-ASCII characters (with the high bit set) are printed as 'M-' (for meta) followed by the character for the low 7 bits. EXIT STATUS
The cat utility exits 0 on success, and >0 if an error occurs. EXAMPLES
The command: cat file1 will print the contents of file1 to the standard output. The command: cat file1 file2 > file3 will sequentially print the contents of file1 and file2 to the file file3, truncating file3 if it already exists. See the manual page for your shell (i.e., sh(1)) for more information on redirection. The command: cat file1 - file2 - file3 will print the contents of file1, print data it receives from the standard input until it receives an EOF ('^D') character, print the con- tents of file2, read and output contents of the standard input again, then finally output the contents of file3. Note that if the standard input referred to a file, the second dash on the command-line would have no effect, since the entire contents of the file would have already been read and printed by cat when it encountered the first '-' operand. SEE ALSO
head(1), more(1), pr(1), sh(1), tail(1), vis(1), zcat(1), setbuf(3) Rob Pike, "UNIX Style, or cat -v Considered Harmful", USENIX Summer Conference Proceedings, 1983. STANDARDS
The cat utility is compliant with the IEEE Std 1003.2-1992 (``POSIX.2'') specification. The flags [-benstv] are extensions to the specification. HISTORY
A cat utility appeared in Version 1 AT&T UNIX. Dennis Ritchie designed and wrote the first man page. It appears to have been cat(1). BUGS
Because of the shell language mechanism used to perform output redirection, the command ``cat file1 file2 > file1'' will cause the original data in file1 to be destroyed! The cat utility does not recognize multibyte characters when the -t or -v option is in effect. BSD
March 21, 2004 BSD
Man Page