scsi_report_lun_scan(9) [suse man page]

SCSI_REPORT_LUN_SCAN(9) 					  SCSI mid layer					   SCSI_REPORT_LUN_SCAN(9)

NAME

       scsi_report_lun_scan - Scan using SCSI REPORT LUN results

SYNOPSIS

       int scsi_report_lun_scan(struct scsi_target * starget, int bflags, int rescan);

ARGUMENTS

       starget
	   which target

       bflags
	   Zero or a mix of BLIST_NOLUN, BLIST_REPORTLUN2, or BLIST_NOREPORTLUN

       rescan
	   nonzero if we can skip code only needed on first scan

DESCRIPTION

       Fast scanning for modern (SCSI-3) devices by sending a REPORT LUN command. Scan the resulting list of LUNs by calling
       scsi_probe_and_add_lun.

       If BLINK_REPORTLUN2 is set, scan a target that supports more than 8 LUNs even if it's older than SCSI-3. If BLIST_NOREPORTLUN is set,
       return 1 always. If BLIST_NOLUN is set, return 0 always.

0
       scan completed (or no memory, so further scanning is futile)

1
       could not scan with REPORT LUN

AUTHORS

       James Bottomley <James.Bottomley@hansenpartnership.com>
	   Author.

       Rob Landley <rob@landley.net>
	   Author.

COPYRIGHT

Kernel Hackers Manual 2.6.					     July 2010						   SCSI_REPORT_LUN_SCAN(9)

RESCAN-SCSI-BUS.SH(1)						   User Commands					     RESCAN-SCSI-BUS.SH(1)

NAME

       rescan-scsi-bus.sh - script for adding and removing SCSI devices without rebooting

SYNOPSIS

       rescan-scsi-bus.sh [options] [host [host ...]]

OPTIONS

       -a, --alltargets
	      scan all targets, not just currently existing [default: disabled]

       -d     enable debug			 [default: 0]

       -l     activates scanning for LUNs 0--7	 [default: 0]

       -L NUM activates scanning for LUNs 0--NUM [default: 0]

       -w, --wide
	      scan for target device IDs 0--15	 [default: 0--7]

       -c     enables scanning of channels 0 1	 [default: 0 / all detected ones]

       -r, --remove
	      enables removing of devices	 [default: disabled]

       -f, --flush
	      flush failed multipath devices	 [default: disabled]

       -i, --issue-lip
	      issue a FibreChannel LIP reset	 [default: disabled]

       -u, --update
	      look for existing disks that have been remapped

       -s, --resize
	      look for resized disks and reload associated multipath devices, if applicable

       --forcerescan
	      rescan existing devices

       --forceremove
	      remove and readd every device (DANGEROUS)

       --nooptscan
	      don't stop looking for LUNs is 0 is not found

       --color
	      use coloured prefixes OLD/NEW/DEL

       --hosts=LIST
	      scan only host(s) in LIST

       --channels=LIST
	      scan only channel(s) in LIST

       --ids=LIST
	      scan only target ID(s) in LIST

       --luns=LIST
	      scan only lun(s) in LIST

       --sync, --nosync
	      issue a sync / no sync [default: sync if remove]

       --attachpq3
	      tell kernel to attach sg to LUN 0 that reports PQ=3

       --reportlun2
	      tell kernel to try REPORT_LUN even on SCSI2 devices

       --largelun
	      tell kernel to support LUNs > 7 even on SCSI2 devs

       --sparselun
	      tell kernel to support sparse LUN numbering

	      Host numbers may thus be specified either directly on cmd line (deprecated) or or with the --hosts=LIST parameter (recommended).

       LIST: A[-B][,C[-D]]... is a comma separated list of single values and ranges (No spaces allowed.)

SEE ALSO

       rescan-scsi-bus.sh Homepage: http://www.garloff.de/kurt/linux/#rescan-scsi

       sg3_utils Homepage: http://sg.danny.cz/sg

rescan-scsi-bus.sh 1.57 					    leden 2014						     RESCAN-SCSI-BUS.SH(1)