put(9e) [sunos man page]
put(9E) Driver Entry Points put(9E) NAME
put - receive messages from the preceding queue SYNOPSIS
#include <sys/types.h> #include <sys/stream.h> #include <sys/stropts.h> #include <sys/ddi.h> #include <sys/sunddi.h> int prefixrput(queue_t *q, mblk_t *mp); /* read side */ int prefixwput(queue_t *q, mblk_t *mp); /* write side */ INTERFACE LEVEL
Architecture independent level 1 (DDI/DKI). This entry point is required for STREAMS. ARGUMENTS
q Pointer to the queue(9S) structure. mp Pointer to the message block. DESCRIPTION
The primary task of the put() routine is to coordinate the passing of messages from one queue to the next in a stream. The put() routine is called by the preceding stream component (stream module, driver, or stream head). put() routines are designated ``write'' or ``read'' depending on the direction of message flow. With few exceptions, a streams module or driver must have a put() routine. One exception is the read side of a driver, which does not need a put() routine because there is no component downstream to call it. The put() routine is always called before the component's correspond- ing srv(9E) (service) routine, and so put() should be used for the immediate processing of messages. A put() routine must do at least one of the following when it receives a message: o pass the message to the next component on the stream by calling the putnext(9F) function; o process the message, if immediate processing is required (for example, to handle high priority messages); or o enqueue the message (with the putq(9F) function) for deferred processing by the service srv(9E) routine. Typically, a put() routine will switch on message type, which is contained in the db_type member of the datab structure pointed to by mp. The action taken by the put() routine depends on the message type. For example, a put() routine might process high priority messages, enqueue normal messages, and handle an unrecognized M_IOCTL message by changing its type to M_IOCNAK (negative acknowledgement) and sending it back to the stream head using the qreply(9F) function. The putq(9F) function can be used as a module's put() routine when no special processing is required and all messages are to be enqueued for the srv(9E) routine. RETURN VALUES
Ignored. CONTEXT
put() routines do not have user context. SEE ALSO
srv(9E), putctl(9F), putctl1(9F), putnext(9F), putnextctl(9F), putnextctl1(9F), putq(9F), qreply(9F), queue(9S), streamtab(9S) Writing Device Drivers STREAMS Programming Guide SunOS 5.10 12 Nov 1992 put(9E)
Check Out this Related Man Page
put(9E) Driver Entry Points put(9E) NAME
put - receive messages from the preceding queue SYNOPSIS
#include <sys/types.h> #include <sys/stream.h> #include <sys/stropts.h> #include <sys/ddi.h> #include <sys/sunddi.h> int prefixrput(queue_t *q, mblk_t *mp); /* read side */ int prefixwput(queue_t *q, mblk_t *mp); /* write side */ INTERFACE LEVEL
Architecture independent level 1 (DDI/DKI). This entry point is required for STREAMS. ARGUMENTS
q Pointer to the queue(9S) structure. mp Pointer to the message block. DESCRIPTION
The primary task of the put() routine is to coordinate the passing of messages from one queue to the next in a stream. The put() routine is called by the preceding stream component (stream module, driver, or stream head). put() routines are designated ``write'' or ``read'' depending on the direction of message flow. With few exceptions, a streams module or driver must have a put() routine. One exception is the read side of a driver, which does not need a put() routine because there is no component downstream to call it. The put() routine is always called before the component's correspond- ing srv(9E) (service) routine, and so put() should be used for the immediate processing of messages. A put() routine must do at least one of the following when it receives a message: o pass the message to the next component on the stream by calling the putnext(9F) function; o process the message, if immediate processing is required (for example, to handle high priority messages); or o enqueue the message (with the putq(9F) function) for deferred processing by the service srv(9E) routine. Typically, a put() routine will switch on message type, which is contained in the db_type member of the datab structure pointed to by mp. The action taken by the put() routine depends on the message type. For example, a put() routine might process high priority messages, enqueue normal messages, and handle an unrecognized M_IOCTL message by changing its type to M_IOCNAK (negative acknowledgement) and sending it back to the stream head using the qreply(9F) function. The putq(9F) function can be used as a module's put() routine when no special processing is required and all messages are to be enqueued for the srv(9E) routine. RETURN VALUES
Ignored. CONTEXT
put() routines do not have user context. SEE ALSO
srv(9E), putctl(9F), putctl1(9F), putnext(9F), putnextctl(9F), putnextctl1(9F), putq(9F), qreply(9F), queue(9S), streamtab(9S) Writing Device Drivers STREAMS Programming Guide SunOS 5.10 12 Nov 1992 put(9E)