hpfc(7d) [sunos man page]

hpfc(7D)							      Devices								  hpfc(7D)

NAME

       hpfc - Agilent fibre channel host bus adapter

SYNOPSIS

       PCI   pci103c

DESCRIPTION

       The hpfc fibre channel host bus adapter is a SCSA compliant nexus driver that supports all Agilent fibre channel host bus adapters, includ-
       ing the HHBA5100x, HHBA5101x, and HHBA5121x models. Agilent host bus adapters support the fibre channel protocol on private  fibre  channel
       arbitrated loops and fabrics. The driver supports up to ten host bus adapters, with a maximum of 125 fibre channel devices on each host bus
       adapter. The hpfc driver supports a maximum of 256 LUNs per target.

       The hpfc driver does not support the BIOS Int 13 feature, which enables the booting of an operating system. As a  result,  you  should  not
       install an operating system on devices attached to the hpfc driver.

CONFIGURATION

       The hpfc driver attempts to configure itself using the information in the /kernel/drv/hpfc.conf configuration file.

       By default, the driver supports only LUN 0 for each target device. To add multiple LUN support, modify the /kernel/drv/sd.conf file.

       Before  upgrading the hpfc driver, backup the sd.conf file to save customized LUN settings and then use pkgrm(1M) to remove the old version
       of the driver.

       The host bus adapter port is initialized to FL_Port when connected to a fabric switch. To change it  to	F_Port,  add  the  init_as_nport=1
       entry to the hpfc.conf file and reboot the system.

       To  conserve system resources, at least one disk drive must be attached to the hpfc driver. If no devices are attached, the driver will not
       load.

FILES

       /kernel/drv/hpfc 	       32-bit ELF kernel module

       /kernel/drv/sparcv9/hpfc        64-bit ELF kernel module

       /kernel/drv/hpfc.conf	       Driver configuration file

       /kernel/drv/sd.conf	       SCSI disk configuration file

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Architecture		     |x86, SPARC		   |
       +-----------------------------+-----------------------------+

SEE ALSO

       luxadm(1M), pkgrm(1M), prtconf(1M), driver.conf(4), attributes(5), ses(7D), ssd(7D)

       ANSI X3.272-1996, Fibre Channel Arbitrated Loop (FC-AL),

       ANSI X3.269-1996, Fibre Channel Protocol for SCSI (FCP),

       ANSI X3.270-1996, SCSI-3 Architecture Model (SAM),

       Fibre Channel Private Loop SCSI Direct Attach (FC-PLDA)

SunOS 5.10							    10 Oct 2000 							  hpfc(7D)

Check Out this Related Man Page

qlc(7D) 							      Devices								   qlc(7D)

NAME

       qlc - ISP2200, ISP2300, and SP212 Family Fibre Channel host bus adapter driver.

SYNOPSIS

       SUNW,qlc

DESCRIPTION

       The qlc host bus adapter driver is a Sun Fibre Channel transport  layer-compliant  nexus driver for the Qlogic ISP2200, ISP2200A,  ISP2310,
       ISP2312, and SP212 adapters. These adapters support  Fibre Channel SCSI and  IP Protocols, FC-AL public loop profile, point-to-point fabric
       connection and Fibre  Channel service classes two and three (see NOTES section below).

       The  qlc driver interfaces with the Sun Fibre Channel transport	layer to support the standard functions provided by the SCSA interface. It
       supports auto request sense and tagged  queueing by default. The driver requires that all devices have unique  hard  addresses  in  private
       loop configurations. Devices with conflicting hard addresses are not accessible.

FILES

       /kernel/drv/qlc		  32-bit ELF kernel module (x86)

       /kernel/drv/amd64/qlc	  64-bit ELF kernel module (x86)

       /kernel/drv/sparcv9/qlc	  64-bit ELF kernel module (SPARC)

       /kernel/drv/qlc.conf	   Driver configuration file

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Architecture		     |SPARC, x86		   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWqlc			   |
       +-----------------------------+-----------------------------+

SEE ALSO

       prtconf(1M), driver.conf(4), fcp(7D), fp(7d)

       Writing Device Drivers

       ANSI X3.230:1994, Fibre Channel Physical Signaling (FC-PH)

       Project 1134-D, Fibre Channel Generic Services (FC-GS-2)

       ANSI X3.269-1996, Fibre Channel Arbitrated Loop (FC-AL)

       ANSI X3.270-1996, Fibre Channel Protocol for  SCSI (FCP-SCSI)

       ANSI X3.270-1996, SCSI-3 Architecture Model (SAM)

       Fibre Channel Private Loop SCSI Direct  Attach  (FC-PLDA)

       Fabric Loop Attachment (FC-FLA)

       ISP2200 Firmware Interface Specification, QLogic Corporation

       ISP2300 Series Firmware Specification, QLogic Corporation

NOTES

	SP-212-based  host bus adapters (including QLA-210) are supported on x86 platforms only and are limited to a maximum of 8  targets in fab-
       ric and sixteen targets in local loop topology. FL topology is not supported with the SP-212-based host bus adapter.

SunOS 5.11							    21 Feb 2005 							   qlc(7D)

Linux and UNIX Man Pages

hpfc(7d) [sunos man page]

Check Out this Related Man Page