Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

ntptrace(1m) [sunos man page]

ntptrace(1M)						  System Administration Commands					      ntptrace(1M)

NAME
ntptrace - trace a chain of NTP hosts back to their master time source SYNOPSIS
/usr/sbin/ntptrace [-vdn] [-r retries] [-t timeout] [server] DESCRIPTION
ntptrace determines where a given Network Time Protocol (NTP) server gets its time from, and follows the chain of NTP servers back to their master time source. If given no arguments, it starts with localhost. OPTIONS
The following options are supported: -d Turns on some debugging output. -n Turns off the printing of host names; instead, host IP addresses are given. This may be necessary if a nameserver is down. -r retries Sets the number of retransmission attempts for each host. -t timeout Sets the retransmission timeout (in seconds); default = 2. -v Prints verbose information about the NTP servers. EXAMPLES
Example 1: Sample Output From the ntptrace Command The following example shows the output from the ntptrace command: % ntptrace localhost: stratum 4, offset 0.0019529, synch distance 0.144135 server2.bozo.com: stratum 2, offset 0.0124263, synch distance 0.115784 usndh.edu: stratum 1, offset 0.0019298, synch distance 0.011993, refid 'WWVB' On each line, the fields are (left to right): o The server's host name o The server's stratum o The time offset between that server and the local host (as measured by ntptrace; this is why it is not always zero for localhost) o The host's synchronization distance o The reference clock ID (only for stratum-1 servers) All times are given in seconds. Synchronization distance is a measure of the goodness of the clock's time. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWntpu | +-----------------------------+-----------------------------+ SEE ALSO
xntpd(1M), attributes(5) BUGS
This program makes no attempt to improve accuracy by doing multiple samples. SunOS 5.10 19 Mar 1998 ntptrace(1M)

Check Out this Related Man Page

ntp(n)								 Tnm Tcl Extension							    ntp(n)

__________________________________________________________________________________________________________________________________________________

NAME
ntp - Retrieve NTP status information. _________________________________________________________________ DESCRIPTION
The Network Time Protocol (NTP) (RFC 1119, RFC 1305) allows to synchronize computer clocks by exchanging NTP messages. The ntp command allows to retrieve control variables from NTP peers. NTP COMMAND
ntp [options] Invoking the ntp command with options but without any command arguments allows to retrieve and change the default values. See the description of supported options below. Default values are bound to a Tcl interpreter which allows to have multiple Tcl interpreter with different defaults. ntp [options] host arrayName The ntp command sends a NTP version 3 mode 6 request to host and writes status information into the Tcl array arrayName. After suc- cessful completion, the array will contain the following elements (RFC 1305): peer.delay This is a signed fixed-point number indicating the roundtrip delay of the peer clock relative to the local clock over the network path between them, in seconds. peer.dispersion This is a signed fixed-point number indicating the maximum error of the peer clock relative to the local clock over the net- work path between them, in seconds. peer.offset This is a signed, fixed-point number indicating the offset of the peer clock relative to the local clock, in seconds. peer.precision This is a signed integer indicating the precision of the various clocks, in seconds to the nearest power of two. peer.reach This is a shift register used to determine the reachability status of the peer, with bits entering from the least significant (rightmost) end. A peer is considered reachable if at least one bit in this register is set to one. peer.srcadr This is the IP address of the peer. peer.stratum This is an integer indicating the stratum of the local clock. peer.valid This is an integer counter indicating the valid samples remaining in the filter register. It is used to determine the reacha- bility state and when the poll interval should be increased or decreased. sys.peer This is a selector identifying the current synchronization source. sys.precision This is a signed integer indicating the precision of the various clocks, in seconds to the nearest power of two. sys.refid This is a 32-bit code identifying the particular reference clock. sys.rootdelay This is a signed fixed-point number indicating the total roundtrip delay to the primary reference source at the root of the synchronization subnet, in seconds. sys.rootdispersion This is a signed fixed-point number indicating the maximum error relative to the primary reference source at the root of the synchronization subnet, in seconds. sys.stratum This is an integer indicating the stratum of the local clock sys.system A textual description of the system type. NTP OPTIONS
The following options control how NTP requests are send and how the ntp command deals with lost NTP packets. -timeout time The -timeout option defines the time the ntp command will wait for a response. The time is defined in seconds with a default of 2 seconds. -retries number The -retries option defines how many times a request is retransmitted during the timeout interval. The default number of retries is 2. SEE ALSO
scotty(1), Tnm(n), Tcl(n) AUTHORS
Erik Schoenfelder <schoenfr@gaertner.de> Juergen Schoenwaelder <schoenw@cs.utwente.nl> Tnm ntp(n)
Man Page