Home Man
Today's Posts

Linux & Unix Commands - Search Man Pages

RedHat 9 (Linux i386) - man page for in.rshd (redhat section 8)

RSHD(8) 			   BSD System Manager's Manual				  RSHD(8)

     rshd -- remote shell server

     rshd [-ahlnL]

     The rshd server is the server for the rcmd(3) routine and, consequently, for the rsh(1) pro-
     gram.  The server provides remote execution facilities with authentication based on privi-
     leged port numbers from trusted hosts.

     The rshd server listens for service requests at the port indicated in the ``cmd'' service
     specification; see services(5).  When a service request is received the following protocol
     is initiated:

     1.   The server checks the client's source port.  If the port is not in the range 512-1023,
	  the server aborts the connection.

     2.   The server reads characters from the socket up to a null (`\0') byte.  The resultant
	  string is interpreted as an ASCII number, base 10.

     3.   If the number received in step 2 is non-zero, it is interpreted as the port number of a
	  secondary stream to be used for the stderr.  A second connection is then created to the
	  specified port on the client's machine.  The source port of this second connection is
	  also in the range 512-1023.

     4.   The server checks the client's source address and requests the corresponding host name
	  (see gethostbyaddr(3), hosts(5) and named(8)).  If the hostname cannot be determined,
	  the dot-notation representation of the host address is used.	If the hostname is in the
	  same domain as the server (according to the last two components of the domain name), or
	  if the -a option is given, the addresses for the hostname are requested, verifying that
	  the name and address correspond.  If address verification fails, the connection is
	  aborted with the message, ``Host address mismatch.''

     5.   A null terminated user name of at most 16 characters is retrieved on the initial
	  socket.  This user name is interpreted as the user identity on the client's machine.

     6.   A null terminated user name of at most 16 characters is retrieved on the initial
	  socket.  This user name is interpreted as a user identity to use on the server's

     7.   A null terminated command to be passed to a shell is retrieved on the initial socket.
	  The length of the command is limited by the upper bound on the size of the system's
	  argument list.

     8.   Rshd then validates the user using ruserok(3), which uses the file /etc/hosts.equiv and
	  the .rhosts file found in the user's home directory. The -l option prevents ruserok(3)
	  from doing any validation based on the user's ``.rhosts'' file (unless the user is the
	  superuser and the -h option is used.) If the -h option is not used, superuser accounts
	  may not be accessed via this service at all.

	  The -l option should not be trusted without verifying that it works as expected with
	  the particular version of libc installed on your system (and should be tested again
	  after any libc update) because some versions of libc may not honor the flags used by

	  Also note that the design of the .rhosts system is COMPLETELY INSECURE except on a
	  carefully firewalled private network. Under all other circumstances, rshd should be
	  disabled entirely.

     9.   A null byte is returned on the initial socket and the command line is passed to the
	  normal login shell of the user.  The shell inherits the network connections established
	  by rshd.

     Transport-level keepalive messages are enabled unless the -n option is present.  The use of
     keepalive messages allows sessions to be timed out if the client crashes or becomes unreach-

     The -L option causes all successful accesses to be logged to syslogd(8) as auth.info mes-
     sages and all failed accesses to be logged as auth.notice.

     Except for the last one listed below, all diagnostic messages are returned on the initial
     socket, after which any network connections are closed.  An error is indicated by a leading
     byte with a value of 1 (0 is returned in step 9 above upon successful completion of all the
     steps prior to the execution of the login shell).

     Locuser too long.
	     The name of the user on the client's machine is longer than 16 characters.

     Ruser too long.
	     The name of the user on the remote machine is longer than 16 characters.

     Command too long.
	     The command line passed exceeds the size of the argument list (as configured into
	     the system).

     Remote directory.
	     The chdir command to the home directory failed.

     Permission denied.
	     The authentication procedure described above failed, or the user requested did not
	     exist. (These conditions are intentionally conflated.)

     Can't make pipe.
	     The pipe needed for the stderr, wasn't created.

     Can't fork; try again.
	     A fork by the server failed.

     <shellname>: ...
	     The user's login shell could not be started.  This message is returned on the con-
	     nection associated with the stderr, and is not preceded by a flag byte.

     rsh(1), rcmd(3), ruserok(3)

     The authentication procedure used here assumes the integrity of each client machine and the
     connecting medium.  This is insecure, but is useful in an ``open'' environment.

     A facility to allow all data exchanges to be encrypted should be present.

     A more extensible protocol (such as Telnet) should be used.

Linux NetKit (0.17)			  April 20, 1991		      Linux NetKit (0.17)

All times are GMT -4. The time now is 10:48 PM.

Unix & Linux Forums Content Copyrightę1993-2018. All Rights Reserved.
Show Password