Query: wavelan
OS: redhat
Section: 4
Format: Original Unix Latex Style Formatted with HTML and a Horizontal Scroll Bar
WAVELAN(4) Kernel Interfaces Manual WAVELAN(4)NAMEwavelan - AT&T GIS WaveLAN ISA device driverSYNOPSISinsmod wavelan_cs.o [io=B,B..] [ irq=I,I..] [name=N,N..]DESCRIPTIONwavelan is the low-level device driver for the NCR / AT&T / Lucent WaveLAN ISA and Digital (DEC) RoamAbout DS wireless ethernet adapter. This driver is available as a module or might be compiled in the kernel. This driver supports multiple cards in both forms (up to 4) and allocates the next available ethernet device (eth0..eth#) for each card found, unless a device name is explicitly specified (see below). This device name will be reported in the kernel log file with the MAC address, NWID and frequency used by the card.PARAMETERSThis section apply to the module form (parameters passed on the insmod(8) command line). If the driver is included in the kernel, use the ether=IRQ,IO,NAME syntax on the kernel command line. io Specify the list of base address where to search for wavelan cards (setting by dip switch on the card). If you don't specify any io address, the driver will scan 0x390 and 0x3E0 addresses, which might conflict with other hardware... irq Set the list of irq that each wavelan card should use (the value is saved in permanent storage for future use). name Set the list of name to be used for each wavelan cards device (name used by ifconfig(8)).WIRELESS EXTENSIONSUse iwconfig(8) to manipulate wireless extensions. NWID (or domain) Set the network ID [0 to FFFF] or disable it [off]. As the NWID is stored in the card Permanent Storage Area, it will be reuse at any fur- ther invocation of the driver. Frequency & channels For the 2.4GHz 2.00 Hardware, you are able to set the frequency by specifying one of the 10 defined channels (2.412, 2.422, 2.425, 2.4305, 2.432, 2.442, 2.452, 2.460, 2.462 or 2.484) or directly by its value. The frequency is changed immediately and permanentely. Frequency availability depend on the regulations... Statistics spy Set a list of MAC addresses in the driver (up to 8) and get the last quality of link for each of those (see iwspy(8)). /proc/net/wireless status is the status reported by the modem. Link quality reports the quality of the modulation on the air (direct sequence spread spec- trum) [max = 16]. Level and Noise refer to the signal level and noise level [max = 64]. The crypt discarded packet and misc discarded packet counters are not implemented.PRIVATE IOCTLYou may use iwpriv(8) to manipulate private ioctls. Quality and Level threshold Enable you the define the quality and level threshold used by the modem (packet below that level are discarded). Histogram This functionality allow to set a number of signal level intervals and to count the number of packets received in each of those defined intervals. This distribution might be used to calculate the mean value and standard deviation of the signal level.SPECIFIC NOTESThis driver will fail to detect some non NCR/ATT&T/Lucent Wavelan cards. If it's your case, you must look in the source code on how to add your card to the detection routine. Some of the mentioned features are optional. You may enable to disable them by changing flags in the driver header and recompile.AUTHORBruce Janson - bruce@cs.usyd.edu.au Jean Tourrilhes - jt@hplb.hpl.hp.com (+ others - see source code for details)SEE ALSOwavelan_cs(4), ifconfig(8), insmod(8), iwconfig(8), iwspy(8), iwpriv(8) Univ. of Sydney (Basser Dep. of Comp. Sci.) 1996-10-22 WAVELAN(4)
Related Man Pages |
---|
wavelan(4) - centos |
iwspy(8) - linux |
iwspy(8) - suse |
iwspy(8) - centos |
iwspy(8) - opensolaris |
Similar Topics in the Unix Linux Community |
---|
ins mod error on eth0 |
unable to bring up any interface |
irq complication |
Naviscore NMS for Lucent Switch Problem |
Changing IP address on NCR UNIX |