AHB(4) BSD Kernel Interfaces Manual AHB(4)NAME
ahb -- Adaptec EISA SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device ahb
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ahb_load="YES"
DESCRIPTION
This driver provides access to the SCSI bus connected to an Adaptec AHA-174X host adapters in ``enhanced'' mode. Tagged queueing and syn-
chronous SCSI transfers are supported.
HARDWARE
The ahb driver supports the following SCSI host adapters:
o Adaptec AHA-1740
o Adaptec AHA-1742
o Adaptec AHA-1740A
o Adaptec AHA-1742A
CAVEATS
The Adaptec 174X is very sensitive to SCSI bus termination and cable length. It may also have difficulties operating with some modern
devices that, due to their speed, expose timing problems in the controller. There are no known mechanisms for working around device incom-
patibilities of this nature.
SEE ALSO aha(4), ahc(4), aic(4), cd(4), da(4), sa(4), scsi(4)AUTHORS
The ahb driver was written by Justin T. Gibbs.
BSD July 4, 2004 BSD
Check Out this Related Man Page
AHB(4) BSD Kernel Interfaces Manual AHB(4)NAME
ahb -- Adaptec EISA SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device ahb
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ahb_load="YES"
DESCRIPTION
This driver provides access to the SCSI bus connected to an Adaptec AHA-174X host adapters in ``enhanced'' mode. Tagged queueing and syn-
chronous SCSI transfers are supported.
HARDWARE
The ahb driver supports the following SCSI host adapters:
o Adaptec AHA-1740
o Adaptec AHA-1742
o Adaptec AHA-1740A
o Adaptec AHA-1742A
CAVEATS
The Adaptec 174X is very sensitive to SCSI bus termination and cable length. It may also have difficulties operating with some modern
devices that, due to their speed, expose timing problems in the controller. There are no known mechanisms for working around device incom-
patibilities of this nature.
SEE ALSO aha(4), ahc(4), aic(4), cd(4), da(4), sa(4), scsi(4)AUTHORS
The ahb driver was written by Justin T. Gibbs.
BSD July 4, 2004 BSD
Hi,
I tried to install Magneto-Optical (MO) drive Fujutsu to COMPAQ Proliant ML350 with SCO Openserver 5.0.5. Harddisk and MO are connected to Adaptec UW-SCSI-3 (driver ad160).
During boot process system shows me that MO is connected to host adapter 1, bus 0, SCSI ID 1 and LUN 0. But when I... (2 Replies)
Hi,
I have installed a SCSI Controller onto an HPUX 10.20b and I don't have any driver files for it when I check in Sys Admin. Do I need to update the kernel? I am not sure how to get the computer to recognize this controller... any suggestions?
Thanks (2 Replies)
I have a UNIX server w/an Adaptec aha-2740 card and i keep getting this error during post: EISA CMOS checksum error. It then tries to boot from the floppy. Upon researching this problem i found that it could be one of two things. Either it is the battery on the m/b (which i have all but ruled out),... (3 Replies)
I am actually trying to find out the following:
Using MS Windows, XP PRO, I downloaded an Adaptec SCSi 39160 driver from SCO Unix site.
Driver is ad160.btld.
I now need to copy this driver to a SCO Unix 5.5 standalone server, via a floppy diskette.
I've tried SCO505 Diskimage and it didn't have... (2 Replies)
Hi
same as last week i came in this morning and the server could not be pinged etc. but the server was on.
I looked in the osmlog file and it had the following:
WARNING: (adsb,1) Adaptec PCI SCSI: Illegal Sector Size (00000000)
WARNING: (adsb,1) Adaptec PCI SCSI: Illegal Sector Size... (1 Reply)