AIO_WRITE(3P) POSIX Programmer's Manual AIO_WRITE(3P)
PROLOG
This manual page is part of the POSIX Programmer's Manual. The Linux implementation of this interface may differ (consult the correspond-
ing Linux manual page for details of Linux behavior), or the interface may not be implemented on Linux.
NAME
aio_write -- asynchronous write to a file
SYNOPSIS
#include <aio.h>
int aio_write(struct aiocb *aiocbp);
DESCRIPTION
The aio_write() function shall write aiocbp->aio_nbytes to the file associated with aiocbp->aio_fildes from the buffer pointed to by
aiocbp->aio_buf. The function shall return when the write request has been initiated or, at a minimum, queued to the file or device.
If prioritized I/O is supported for this file, then the asynchronous operation shall be submitted at a priority equal to a base scheduling
priority minus aiocbp->aio_reqprio. If Thread Execution Scheduling is not supported, then the base scheduling priority is that of the call-
ing process;
otherwise, the base scheduling priority is that of the calling thread.
The aiocbp argument may be used as an argument to aio_error() and aio_return() in order to determine the error status and return status,
respectively, of the asynchronous operation while it is proceeding.
The aiocbp argument points to an aiocb structure. If the buffer pointed to by aiocbp->aio_buf or the control block pointed to by aiocbp
becomes an illegal address prior to asynchronous I/O completion, then the behavior is undefined.
If O_APPEND is not set for the file descriptor aio_fildes, then the requested operation shall take place at the absolute position in the
file as given by aio_offset, as if lseek() were called immediately prior to the operation with an offset equal to aio_offset and a whence
equal to SEEK_SET. If O_APPEND is set for the file descriptor, or if aio_fildes is associated with a device that is incapable of seeking,
write operations append to the file in the same order as the calls were made, except under circumstances described in Section 2.8.2, Asyn-
chronous I/O. After a successful call to enqueue an asynchronous I/O operation, the value of the file offset for the file is unspecified.
The aio_sigevent member specifies the notification which occurs when the request is completed.
The aiocbp->aio_lio_opcode field shall be ignored by aio_write().
Simultaneous asynchronous operations using the same aiocbp produce undefined results.
If synchronized I/O is enabled on the file associated with aiocbp->aio_fildes, the behavior of this function shall be according to the def-
initions of synchronized I/O data integrity completion, and synchronized I/O file integrity completion.
For any system action that changes the process memory space while an asynchronous I/O is outstanding to the address range being changed,
the result of that action is undefined.
For regular files, no data transfer shall occur past the offset maximum established in the open file description associated with
aiocbp->aio_fildes.
RETURN VALUE
The aio_write() function shall return the value zero if the I/O operation is successfully queued; otherwise, the function shall return the
value -1 and set errno to indicate the error.
ERRORS
The aio_write() function shall fail if:
EAGAIN The requested asynchronous I/O operation was not queued due to system resource limitations.
Each of the following conditions may be detected synchronously at the time of the call to aio_write(), or asynchronously. If any of the
conditions below are detected synchronously, the aio_write() function shall return -1 and set errno to the corresponding value. If any of
the conditions below are detected asynchronously, the return status of the asynchronous operation shall be set to -1, and the error status
of the asynchronous operation is set to the corresponding value.
EBADF The aiocbp->aio_fildes argument is not a valid file descriptor open for writing.
EINVAL The file offset value implied by aiocbp->aio_offset would be invalid,
aiocbp->aio_reqprio is not a valid value, or aiocbp->aio_nbytes is an invalid value.
In the case that the aio_write() successfully queues the I/O operation, the return status of the asynchronous operation shall be one of the
values normally returned by the write() function call. If the operation is successfully queued but is subsequently canceled or encounters
an error, the error status for the asynchronous operation contains one of the values normally set by the write() function call, or one of
the following:
EBADF The aiocbp->aio_fildes argument is not a valid file descriptor open for writing.
EINVAL The file offset value implied by aiocbp->aio_offset would be invalid.
ECANCELED
The requested I/O was canceled before the I/O completed due to an explicit aio_cancel() request.
The following condition may be detected synchronously or asynchronously:
EFBIG The file is a regular file, aiobcp->aio_nbytes is greater than 0, and the starting offset in aiobcp->aio_offset is at or beyond the
offset maximum in the open file description associated with aiocbp->aio_fildes.
The following sections are informative.
EXAMPLES
None.
APPLICATION USAGE
None.
RATIONALE
None.
FUTURE DIRECTIONS
None.
SEE ALSO
Section 2.8.2, Asynchronous I/O, aio_cancel(), aio_error(), aio_read(), aio_return(), close(), exec, exit(), fork(), lio_listio(), lseek(),
write()
The Base Definitions volume of POSIX.1-2008, <aio.h>
COPYRIGHT
Portions of this text are reprinted and reproduced in electronic form from IEEE Std 1003.1, 2013 Edition, Standard for Information Technol-
ogy -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 7, Copyright (C) 2013 by the Institute of
Electrical and Electronics Engineers, Inc and The Open Group. (This is POSIX.1-2008 with the 2013 Technical Corrigendum 1 applied.) In the
event of any discrepancy between this version and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Stan-
dard is the referee document. The original Standard can be obtained online at http://www.unix.org/online.html .
Any typographical or formatting errors that appear in this page are most likely to have been introduced during the conversion of the source
files to man page format. To report such errors, see https://www.kernel.org/doc/man-pages/reporting_bugs.html .
IEEE
/The Open Group 2013 AIO_WRITE(3P)