UATH(4) BSD Kernel Interfaces Manual UATH(4)
NAME
uath -- Atheros USB IEEE 802.11a/b/g wireless network device
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device ehci
device uhci
device ohci
device usb
device uath
device wlan
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_uath_load="YES"
DESCRIPTION
The uath driver supports USB 2.0 wireless network devices based on Atheros Communications fifth generation AR5005UG and AR5005UX chipsets.
The AR5005UG chipset is made of an AR5523 multiprotocol MAC/baseband processor and an AR2112 Radio-on-a-Chip that can operate between 2300
and 2500 MHz (802.11b/g).
The AR5005UX chipset is made of an AR5523 multiprotocol MAC/baseband processor and an AR5112 dual band Radio-on-a-Chip that can operate
between 2300 and 2500 MHz (802.11b/g) or 4900 and 5850 MHz (802.11a).
The AR5005UG and AR5005UX chipsets both have an integrated 32-bit MIPS R4000-class processor that runs a firmware and manages, among other
things, the automatic control of the transmit rate and the calibration of the radio.
uath supports station, and monitor mode operation. Only one virtual interface may be configured at any time. For more information on con-
figuring this device, see ifconfig(8).
FIRMWARE
uath requires firmware that is downloaded to the device. This is normally done by the uathload(8) utility that is launched by devd(8) when
the device is inserted. uathload includes the firmware in the binary program. This firmware is licensed for general use and is included in
the base system.
HARDWARE
The uath driver should work with the following adapters:
Adapter Chipset
Compex WLU108AG AR5005UX
Compex WLU108G AR5005UG
D-Link DWL-G132 AR5005UG
IODATA WN-G54/US AR5005UG
MELCO WLI-U2-KAMG54 AR5005UX
Netgear WG111T AR5005UG
Netgear WG111U AR5005UX
Netgear WPN111 AR5005UG
Olitec 000544 AR5005UG
PLANET WDL-U357 AR5005UX
Siemens Gigaset 108 AR5005UG
SMC SMCWUSBT-G AR5005UG
SMC SMCWUSBT-G2 AR5005UG
SparkLAN WL-785A AR5005UX
TP-Link TL-WN620G AR5005UG
TRENDware International TEW-444UB AR5005UG
TRENDware International TEW-504UB AR5005UX
Unex Technology UR054ag AR5005UX
ZyXEL XtremeMIMO M-202 AR5005UX
An up to date list can be found at http://customerproducts.atheros.com/customerproducts/default.asp.
EXAMPLES
Join an existing BSS network (i.e., connect to an access point):
ifconfig wlan create wlandev uath0 inet 192.168.0.20
netmask 0xffffff00
Join a specific BSS network with network name ``my_net'':
ifconfig wlan create wlandev uath0 ssid my_net up
Join a specific BSS network with 64-bit WEP encryption:
ifconfig wlan create wlandev uath0 ssid my_net
wepmode on wepkey 0x1234567890 weptxkey 1 up
Join a specific BSS network with 128-bit WEP encryption:
ifconfig wlan create wlandev uath0 wlanmode adhoc ssid my_net
wepmode on wepkey 0x01020304050607080910111213 weptxkey 1
DIAGNOSTICS
uath%d: could not send command (error=%s) An attempt to send a command to the firmware failed.
uath%d: timeout waiting for command reply A read command was sent to the firmware but the firmware failed to reply in time.
uath%d: device timeout A frame dispatched to the hardware for transmission did not complete in time. The driver will reset the hardware.
This should not happen.
SEE ALSO
netintro(4), usb(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), devd(8), ifconfig(8), uathload(8), wpa_supplicant(8)
HISTORY
The uath driver first appeared in OpenBSD 4.0.
AUTHORS
The uath driver was written by Weongyo Jeong <weongyo@freebsd.org> and Sam Leffler <sam@freebsd.org>. It is distantly related to a driver
written by Damien Bergamini <damien@openbsd.org>.
CAVEATS
Atheros proprietary 108 Mbps mode (aka Super AG mode) is not supported.
Dual-band adapters are presently not working; to workaround, restriction operation to 2.4GHz channels.
BSD
April 7, 2009 BSD