XIMAGE(1) General Commands Manual XIMAGE(1)
ximage - RADIANCE picture display for X window system
ximage [ =geometry ][ -di display ][ -c ncolors ][ -d ][ -b ][ -m ][ -g gamma ][ -f ][ -e spec ][ -ospec ][ -t intvl ][ -s ] picture ..
Ximage takes one or more RADIANCE picture files and displays them on an X server. The -c option specifies the number of colors to use
(default fills color table). The -d option turns off color dithering. The -b option displays the image in black and white (greyscale).
The -m option forces monochrome output. The -g option specifies the exponent used in gamma correction; the default value is 2.2. The -f
option stores a Pixmap on the server side for faster refresh. This may not work with large images on some servers. The -o option speci-
fies a sequence of information to print to the standard output for the 't' command (see below). The -t option specifies a minimum interval
(in milliseconds) between successive ray outputs in mouse tracking mode (right button pressed).
The -e option specifies an exposure compensation in f-stops (powers of two). Only integer stops are allowed, for efficiency. If the spe-
cial word, auto is given instead of a number of stops, then ximage performs an automatic exposure adjustment similar to pcond(1), compress-
ing the dynamic range of the image to fit within the dynamic range of the display. If the special word, human is given instead, then xim-
age performs an exposure adjustment similar to pcond with the -s and -c options, which compensate for human contrast and color sensitivity
at the corresponding scene luminance levels. This option yields and appearance of the scene on the display that closely matches what would
be experienced in the real world.
The -s option tells ximage to display multiple pictures sequentially, rather than all at once. If no picture is given, input is read from
stdin provided either the -b or -m option is in effect, or the X server is capable of 24-bit color. However, many of the commands given
below will not work.
Once a picture is displayed, the user may perform a number of operations. Some of the operations make use of an area of interest, defined
by pressing the left mouse button and dragging the cursor over a section of the image. Pressing the button and immediately releasing it
defines a single point as the area of interest. A command is a single character.
q Quit picture. (Also Q or ^D.)
<space> Redraw the area of interest.
^R Redraw the entire image.
<return> Display the radiance averaged over the area of interest. The maximum of the three (RGB) channels is reported.
l Display the photometrically-weighted luminance value in the area of interest. This assumes that the image was correctly computed
in terms of luminance.
c Display the color in the area of interest, as adjusted by the current exposure setting.
p Display the x and y location of the cursor.
i Identify identical pixels by assigning a random color at the cursor position. This is useful for displaying contours, especially
when combined with the -b option.
t Print information about the pixel under the cursor according to the string following the -o command line option. The valid char-
acters for this option correspond roughly to the other ximage commands:
o ray origin
d ray direction
v radiance value
l luminance value
p pixel position
The default output is "-ood", which prints the ray origin and direction. This can be used as input to rtrace(1) to get addi-
tional information about the image (ie. pipe the output of ximage into rtrace). Pressing the middle mouse button is equivalent
to typing the 't' key. Pressing and holding the right mouse button is equivalent to continuously pressing the 't' key.
= Adjust the exposure to the area of interest. A crude adjustment is made immediately, and the number of stops is printed while
the colors are resampled. After a few seconds to a minute, the final image is redisplayed. If the area of interest is already
within 1/2 stop of the ideal, no adjustment is made.
@ Same as '=' command, only the exposure is adjusted to provide roughly the same visibility for the selected region on screen as a
viewer would experience in the actual space. Like the 'l' command, this adjustment assumes that the image has been correctly
computed in terms of luminance. (See also the 'h' command, below.)
a Perform automatic exposure compensation, as if ximage were started with the -e auto option. If a rectangular area has been
selected, the pixels in this region will be emphasized in the histogram, offering this area exposure preference. (Each pixel
within the rectangle will be weighted as 21 outside pixels.)
h Perform human expsoure compensation, as if ximage were started with the -e human option. See the 'a' command above regarding
0 Reset the origin to the upper left corner of the image. This command is used to restore the original image position after using
the shift or control key with the mouse to relocate the image within the frame (see below).
f Switch on the fast redraw option (-f), loading the image pixmap over to the server side. This command is useful when network
delays are causing slow image refresh, and the user didn't notice it until after ximage was started.
F Switch off the fast redraw option. This frees up some memory on the server, as well as the color table for other windows.
In addition to the commands listed above, the control or shift key may be held while the cursor is dragged to reposition the image within
radiance.gamma the default gamma correction value
DISPLAY_GAMMA the default gamma correction value
Anat Grynberg (Paris)
Philip Thompson (MIT)
aedimage(1), normtiff(1), pcond(1), pfilt(1), rpict(1), rtrace(1), rvu(1), xglaresrc(1), xshowtrace(1)