JOT(1) BSD General Commands Manual JOT(1)
jot -- print sequential or random data
jot [-cnr] [-b word] [-w word] [-s string] [-p precision] [reps [begin [end [s]]]]
The jot utility is used to print out increasing, decreasing, random, or redundant data, usually numbers, one per line.
The following options are available:
-r Generate random data instead of the default sequential data.
Just print word repetitively.
Print word with the generated data appended to it. Octal, hexadecimal, exponential, ASCII, zero padded, and right-adjusted represen-
tations are possible by using the appropriate printf(3) conversion specification inside word, in which case the data are inserted
rather than appended.
-c This is an abbreviation for -w %c.
Print data separated by string. Normally, newlines separate data.
-n Do not print the final newline normally appended to the output.
Print only as many digits or characters of the data as indicated by the integer precision. In the absence of -p, the precision is
the greater of the precisions of begin and end. The -p option is overridden by whatever appears in a printf(3) conversion following
The last four arguments indicate, respectively, the number of data, the lower bound, the upper bound, and the step size or, for random data,
the seed. While at least one of them must appear, any of the other three may be omitted, and will be considered as such if given as - or as
an empty string. Any three of these arguments determines the fourth. If four are specified and the given and computed values of reps con-
flict, the lower value is used. If fewer than three are specified, defaults are assigned left to right, except for s, which assumes a
default of 1 or -1 if both begin and end are given.
Defaults for the four arguments are, respectively, 100, 1, 100, and 1, except that when random data are requested, the seed, s, is picked
randomly. The reps argument is expected to be an unsigned integer, and if given as zero is taken to be infinite. The begin and end argu-
ments may be given as real numbers or as characters representing the corresponding value in ASCII. The last argument must be a real number.
Random numbers are obtained through arc4random(3) when no seed is specified, and through random(3) when a seed is given. When jot is asked
to generate random integers or characters with begin and end values in the range of the random number generator function and no format is
specified with one of the -w, -b, or -p options, jot will arrange for all the values in the range to appear in the output with an equal prob-
ability. In all other cases be careful to ensure that the output format's rounding or truncation will not skew the distribution of output
values in an unintended way.
The name jot derives in part from iota, a function in APL.
The jot utility exits 0 on success, and >0 if an error occurs.
jot - 1 10
prints the integers from 1 to 10, while the command
jot 21 -1 1.00
prints 21 evenly spaced numbers increasing from -1 to 1. The ASCII character set is generated with
jot -c 128 0
and the strings xaa through xaz with
jot -w xa%c 26 a
while 20 random 8-letter strings are produced with
jot -r -c 160 a z | rs -g 0 8
Infinitely many yes's may be obtained through
jot -b yes 0
and thirty ed(1) substitution commands applying to lines 2, 7, 12, etc. is the result of
jot -w %ds/old/new/ 30 2 - 5
The stuttering sequence 9, 9, 8, 8, 7, etc. can be produced by suitable choice of step size, as in
jot - 9 0 -.5
and a file containing exactly 1024 bytes is created with
jot -b x 512 > block
Finally, to set tabs four spaces apart starting from column 10 and ending in column 132, use
expand -`jot -s, - 10 132 4`
and to print all lines 80 characters or longer,
grep `jot -s "" -b . 80`
The following diagnostic messages deserve special explanation:
illegal or unsupported format '%s' The requested conversion format specifier for printf(3) was not of the form
where ``?'' must be one of
range error in conversion A value to be printed fell outside the range of the data type associated with the requested output format.
too many conversions More than one conversion format specifier has been supplied, but only one is allowed.
ed(1), expand(1), rs(1), seq(1), yes(1), arc4random(3), printf(3), random(3)
The jot utility first appeared in 4.2BSD.
February 19, 2010 BSD