issue.net(4) Kernel Interfaces Manual issue.net(4)NAME
issue.net - Network issue identification file
DESCRIPTION
The /etc/issue.net file is a freely formatted ASCII file. If present, the telnetd daemon reads this file and writes its contents over a
new telnet connection prior to starting the login dialog.
Use this file to store messages that are longer than the message field for entries in the /etc/gettydefs file.
Note
You must be aware of the size limits of all potential output devices as you create /etc/issue.net messages. Some devices (for example,
small screens) might not hold the messages you enter into the file and will truncate the messages.
FILES
Specifies the path name for the file.
RELATED INFORMATION
Commands: getty(8), telnetd(8).
Files: issue(4). delim off
issue.net(4)
Check Out this Related Man Page
telnetd(8) System Manager's Manual telnetd(8)NAME
telnetd - The DARPA telnet protocol server
SYNOPSIS
telnetd [-debug [port]] [-D modifier ...]
FLAGS
Starts telnetd manually, rather than through inetd, on alternate TCP port number port (if specified). Prints out debugging information.
modifiers are: Prints information about negotiation of telnet options Same as options with additional processing information Displays the
data stream received by telnetd Displays data written to the pty Not yet implemented
DESCRIPTION
The telnetd daemon is a server that supports the DARPA (Defense Advanced Research Projects Agency) standard telnet virtual terminal proto-
col. telnetd is invoked by the Internet server (see inetd(8)) normally for requests to connect to the telnet port as indicated by the
/etc/services file (see services(4)). The -debug flag may be used, to start up telnetd manually. If started up this way, port may be
specified to run telnetd on an alternate TCP port number.
The -D options may be used for debugging purposes. This allows telnetd to print out debugging information to the connection, allowing the
user to see what telnetd is doing.
The telnetd daemon operates by allocating a pseudoterminal device (see pty(7)) for a client, then creating a login process that has the
slave side of the pseudoterminal as stdin, stdout, and stderr. telnetd manipulates the master side of the pseudo-terminal, implementing
the telnet protocol and passing characters between the remote client and the login process.
When a telnet session is started up, telnetd sends telnet options to the client side, indicating a willingness to do remote echo of charac-
ters, to suppress go ahead, to do remote flow control, and to receive terminal type information, terminal speed information, and window
size information from the remote client. If the remote client is willing, the remote terminal type is propagated in the environment of the
created login process. The pseudoterminal allocated to the client is configured to operate in cooked mode, and with XTABS and CRMOD
enabled (see tty(7)).
The telnetd daemon is willing to do: echo, binary, suppress go ahead, and timing mark. telnetd is willing to have the remote client do:
line mode, binary, terminal type, terminal speed, window size, toggle flow control, environment, X display location, and suppress go ahead.
The telnetd daemon never sends telnet go ahead commands.
Note that binary mode has no common interpretation except between similar operating systems (Unix compatible systems in this case).
Note also that the terminal type name received from the remote client is converted to lowercase.
The telnet command uses the default Type-of-Service value recommended by RFC1060, which is as follows: Low delay
You can configure this value by specifying it in the /etc/iptos file. For more information, see iptos(4).
By default, the telnetd daemon starts the login dialog using the login string specified in the message field of the /etc/gettydefs file.
If you want to use a customized banner, create an /etc/issue.net or /etc/issue file. The telnetd daemon reads the file that exists and
writes its contents over a new telnet connection prior to starting the login dialog. If both files exist, only the /etc/issue.net file is
used.
CAUTIONS
Some telnet commands are only partially implemented.
Because of bugs in the original 4.2BSD telnet(1), telnetd performs some dubious protocol exchanges to try to discover if the remote client
is, in fact, a 4.2BSD telnet(1).
FILES
Specifies the command path. Specifies the path name for the network issue identification file. Specifies the path name for the issue
identification file.
RELATED INFORMATION
Commands: telnet(1).
Files: iptos(4), issue(4), issue.net(4). delim off
telnetd(8)