fs(4) Kernel Interfaces Manual fs(4)
NAME
fs, inode - Specifies the format of the file system volume
SYNOPSIS
#include <sys/types.h> #include <sys/fs.h> #include <ufs/inode.h>
DESCRIPTION
Every file system storage volume (disk, nine-track tape, for instance) has a common format for certain vital information. Each such volume
is divided into a certain number of blocks. The block size is a parameter of the file system. Sectors beginning at BBLOCK and continuing
for BBSIZE are used to contain a label and for some hardware primary and secondary bootstrapping programs.
Each disk drive contains some number of file systems. A file system consists of a number of cylinder groups. Each cylinder group has
inodes and data.
A file system is described by its superblock, which in turn describes the cylinder groups. The superblock is critical data and is repli-
cated in each cylinder group to protect against loss of data. This is done at file system creation time and the critical superblock data
does not change, so the copies need not be referenced further until necessary.
Addresses stored in inodes are capable of addressing fragments of blocks. File system blocks of at most MAXBSIZE size can be optionally
broken into 2, 4, or 8 pieces, each of which is addressable; these pieces may be DEV_BSIZE, or some multiple of a DEV_BSIZE unit.
Large files consist exclusively of large data blocks. To avoid wasted disk space, the last data block of a small file is allocated only as
many fragments of a large block as are necessary. The file system format retains only a single pointer to such a fragment, which is a
piece of a single large block that has been divided. The size of such a fragment is determined from information in the inode, using the
blksize(fs, ip, lbn) macro.
The file system records space availability at the fragment level; to determine block availability, aligned fragments are examined.
The root inode is the root of the file system. Inode 0 (zero) can't be used for normal purposes and, historically, bad blocks were linked
to inode 1. Thus, the root inode is 2 (inode 1 is no longer used for this purpose, but numerous dump tapes make this assumption).
Some fields to the fs structure are as follows: Gives the minimum acceptable percentage of file system blocks that may be free. If the
freelist drops below this level only the superuser may continue to allocate blocks. The fs_minfree field may be set to 0 (zero) if no
reserve of free blocks is deemed necessary. However, severe performance degradations will be observed if the file system is run at greater
than 90% full; thus the default value of the fs_minfree field is 10%.
Empirically the best trade-off between block fragmentation and overall disk utilization at a loading of 90% comes with a fragmenta-
tion of 8, thus the default fragment size is an eighth of the block size. Specifies whether the file system should try to minimize
the time spent allocating blocks, or if it should attempt to minimize the space fragmentation on the disk. If the value of fs_min-
free is less than 10%, then the file system defaults to optimizing for space to avoid running out of full sized blocks. If the
value of fs_minfree is greater than or equal to 10%, fragmentation is unlikely to be problematical, and the file system defaults to
optimizing for time.
Cylinder group related limits: Each cylinder keeps track of the availability of blocks at different positions of rotation, so that
sequential blocks can be laid out with minimum rotational latency. With the default of 8 distinguished rotational positions, the
resolution of the summary information is 2 milliseconds for a typical 3600 rpm drive. Gives the minimum number of milliseconds to
initiate another disk transfer on the same cylinder. The fs_rotdelay field is used in determining the rotationally optimal layout
for disk blocks within a file; the default value for fs_rotdelay is 2 milliseconds.
Each file system has a statically allocated number of inodes. An inode is allocated for each NBPI bytes of disk space. The inode alloca-
tion strategy is extremely conservative.
MINBSIZE is the smallest allowable block size. With a MINBSIZE of 4096 it is possible to create files of size 232 with only two levels of
indirection. MINBSIZE must be big enough to hold a cylinder group block, thus changes to struct cg must keep its size within MINBSIZE.
Note that superblocks are never more than size SBSIZE.
The pathname on which the file system is mounted is maintained in fs_fsmnt. MAXMNTLEN defines the amount of space allocated in the
superblock for this name. The limit on the amount of summary information per file system is defined by MAXCSBUFS. For a 4096 byte block
size, it is currently parameterized for a maximum of two million cylinders.
Per cylinder group information is summarized in blocks allocated from the first cylinder group's data blocks. These blocks are read in
from fs_csaddr (size fs_cssize) in addition to the superblock.
Superblock for a file system: The size of the rotational layout tables is limited by the fact that the superblock is of size SBSIZE. The
size of these tables is inversely proportional to the block size of the file system. The size of the tables is increased when sector sizes
are not powers of two, as this increases the number of cylinders included before the rotational pattern repeats (fs_cpc). The size of the
rotational layout tables is derived from the number of bytes remaining in (struct fs).
The number of blocks of data per cylinder group is limited because cylinder groups are at most one block. The inode and free block tables
must fit into a single block after deducting space for the cylinder group structure struct cg.
Inode: The inode is the focus of all file activity in the UNIX file system. There is a unique inode allocated for each active file, each
current directory, each mounted-on file, text file, and the root. An inode is `named' by its device/i-number pair.
NOTES
sizeof (struct csum) must be a power of two in order for the fs_cs macro to work. delim off
fs(4)