DA(4) BSD Kernel Interfaces Manual DA(4)
NAME
da -- SCSI Direct Access device driver
SYNOPSIS
device da
DESCRIPTION
The da driver provides support for all SCSI devices of the direct access class that are attached to the system through a supported SCSI Host
Adapter. The direct access class includes disk, magneto-optical, and solid-state devices.
A SCSI Host adapter must also be separately configured into the system before a SCSI direct access device can be configured.
CACHE EFFECTS
Many direct access devices are equipped with read and/or write caches. Parameters affecting the device's cache are stored in mode page 8,
the caching control page. Mode pages can be examined and modified via the camcontrol(8) utility.
The read cache is used to store data from device-initiated read ahead operations as well as frequently used data. The read cache is trans-
parent to the user and can be enabled without any adverse effect. Most devices with a read cache come from the factory with it enabled. The
read cache can be disabled by setting the RCD (Read Cache Disable) bit in the caching control mode page.
The write cache can greatly decrease the latency of write operations and allows the device to reorganize writes to increase efficiency and
performance. This performance gain comes at a price. Should the device lose power while its cache contains uncommitted write operations,
these writes will be lost. The effect of a loss of write transactions on a file system is non-deterministic and can cause corruption. Most
devices age write transactions to limit vulnerability to a few transactions recently reported as complete, but it is none-the-less recom-
mended that systems with write cache enabled devices reside on an Uninterruptible Power Supply (UPS). The da device driver ensures that the
cache and media are synchronized upon final close of the device or an unexpected shutdown (panic) event. This ensures that it is safe to
disconnect power once the operating system has reported that it has halted. The write cache can be enabled by setting the WCE (Write Cache
Enable) bit in the caching control mode page.
TAGGED QUEUING
The da device driver will take full advantage of the SCSI feature known as tagged queueing. Tagged queueing allows the device to process
multiple transactions concurrently, often re-ordering them to reduce the number and length of seeks. To ensure that transactions to distant
portions of the media, which may be deferred indefinitely by servicing requests nearer the current head position, are completed in a timely
fashion, an ordered tagged transaction is sent every 15 seconds during continuous device operation.
BAD BLOCK RECOVERY
Direct Access devices have the capability of mapping out portions of defective media. Media recovery parameters are located in mode page 1,
the Read-Write Error Recovery mode page. The most important media remapping features are 'Auto Write Reallocation' and 'Auto Read Realloca-
tion' which can be enabled via the AWRE and ARRE bits, respectively, of the Read-Write Error Recovery page. Many devices do not ship from
the factory with these feature enabled. Mode pages can be examined and modified via the camcontrol(8) utility.
KERNEL CONFIGURATION
It is only necessary to explicitly configure one da device; data structures are dynamically allocated as disks are found on the SCSI bus.
SYSCTL VARIABLES
The following variables are available as both sysctl(8) variables and loader(8) tunables:
kern.cam.da.retry_count
This variable determines how many times the da driver will retry a READ or WRITE command. This does not affect the number of retries
used during probe time or for the da driver dump routine. This value currently defaults to 4.
kern.cam.da.default_timeout
This variable determines how long the da driver will wait before timing out an outstanding command. The units for this value are sec-
onds, and the default is currently 60 seconds.
kern.cam.da.%d.minimum_cmd_size
This variable determines what the minimum READ/WRITE CDB size is for a given da unit. (The %d above denotes the unit number of the da
driver instance, e.g. 1, 2, 4, 8, etc.) Valid minimum command size values are 6, 10, 12 and 16 bytes. The default is 6 bytes.
The da driver issues a CAM Path Inquiry CCB at probe time to determine whether the protocol the device in question speaks (e.g. ATAPI)
typically does not allow 6 byte commands. If it does not, the da driver will default to using at least 10 byte CDBs. If a 6 byte READ
or WRITE fails with an ILLEGAL REQUEST error, the da driver will then increase the default CDB size for the device to 10 bytes and retry
the command. CDB size is always chosen as the smallest READ/WRITE CDB that will satisfy the specified minimum command size, and the LBA
and length of the READ or WRITE in question. (e.g., a write to an LBA larger than 2^32 will require a 16 byte CDB.)
NOTES
If a device becomes invalidated (media is removed, device becomes unresponsive) the disklabel and information held within the kernel about
the device will be invalidated. To avoid corruption of a newly inserted piece of media or a replacement device, all accesses to the device
will be discarded until the last file descriptor referencing the old device is closed. During this period, all new open attempts will be
rejected.
FILES
/dev/da* SCSI disk device nodes
DIAGNOSTICS
None.
SEE ALSO
ad(4), cam(4), geom(4), bsdlabel(8), fdisk(8)
HISTORY
The da driver was written for the CAM SCSI subsystem by Justin T. Gibbs. Many ideas were gleaned from the sd device driver written and
ported from Mach 2.5 by Julian Elischer.
BSD September 2, 2003 BSD