reboot(2) [osf1 man page]

reboot(2)							System Calls Manual							 reboot(2)

NAME

       reboot - Reboots system or halts processor

SYNOPSIS

       #include <sys/reboot.h>
       void reboot(	 int howto );

PARAMETERS

       Specifies a mask of options.

DESCRIPTION

       The reboot() function restarts the system.  The startup is automatic and brings up /vmunix in the normal, nonmaintenance mode.  The calling
       process must have superuser privilege to run this function successfully.  However, a reboot is invoked automatically in the event of  unre-
       coverable system failures.

       The  following options, defined in the sys/reboot.h include file are passed to the new kernel or the new bootstrap and init programs.  They
       are supplied as values to the howto parameter.  The default, causing the system to reboot in its usual fashion.	Dump kernel memory  before
       rebooting; see the savecore command for more information.  The processor is simply halted; no reboot takes place.  The disks are not sync'd
       before the processor is halted or rebooted.  Normally, the disks are sync'd (see the sync() command) before  the  processor  is	halted	or
       rebooted.  Because the disks are not sync'd with the RB_NOSYNC option, loss of data may result from using it.

       When  no options are given (that is, RB_AUTOBOOT is used), the system is rebooted from file vmunix in the root file system of unit 0 (zero)
       of a disk chosen in a processor-specific way.  (see the fsck command).

RETURN VALUES

       If successful, this call does not return.  Otherwise, a -1 is returned and errno is set to indicate the error.

ERRORS

       If the reboot() function fails, errno may be set to the following value: The calling process does not have appropriate privilege.

RELATED INFORMATION

       Commands: crashdc(8),

       halt(8), init(8), reboot(8), savecore(8) delim off

																	 reboot(2)

REBOOT(2)						      BSD System Calls Manual							 REBOOT(2)

NAME

     reboot -- reboot system or halt processor

LIBRARY

     Standard C Library (libc, -lc)

SYNOPSIS

     #include <unistd.h>
     #include <sys/reboot.h>

     int
     reboot(int howto);

DESCRIPTION

     The reboot() system call reboots the system.  Only the super-user may reboot a machine on demand.	However, a reboot is invoked automatically
     in the event of unrecoverable system failures.

     The howto argument is a mask of options; the system call interface allows the following options, defined in the include file <sys/reboot.h>,
     to be passed to the new kernel or the new bootstrap and init programs.

     RB_AUTOBOOT   The default, causing the system to reboot in its usual fashion.

     RB_ASKNAME    Interpreted by the bootstrap program itself, causing it to prompt on the console as to what file should be booted.  Normally,
		   the system is booted from the file ``xx(0,0)kernel'', where xx is the default disk name, without prompting for the file name.

     RB_DFLTROOT   Use the compiled in root device.  Normally, the system uses the device from which it was booted as the root device if possible.
		   (The default behavior is dependent on the ability of the bootstrap program to determine the drive from which it was loaded,
		   which is not possible on all systems.)

     RB_DUMP	   Dump kernel memory before rebooting; see savecore(8) for more information.

     RB_HALT	   the processor is simply halted; no reboot takes place.  This option should be used with caution.

     RB_POWEROFF   After halting, the shutdown code will do what it can to turn off the power.	This requires hardware support.

     RB_INITNAME   An option allowing the specification of an init program (see init(8)) other than /sbin/init to be run when the system reboots.
		   This switch is not currently available.

     RB_KDB	   Load the symbol table and enable a built-in debugger in the system.	This option will have no useful function if the kernel is
		   not configured for debugging.  Several other options have different meaning if combined with this option, although their use
		   may not be possible via the reboot() system call.  See ddb(4) for more information.

     RB_NOSYNC	   Normally, the disks are sync'd (see sync(8)) before the processor is halted or rebooted.  This option may be useful if file
		   system changes have been made manually or if the processor is on fire.

     RB_RDONLY	   Initially mount the root file system read-only.  This is currently the default, and this option has been deprecated.

     RB_SINGLE	   Normally, the reboot procedure involves an automatic disk consistency check and then multi-user operations.	RB_SINGLE prevents
		   this, booting the system with a single-user shell on the console.  RB_SINGLE is actually interpreted by the init(8) program in
		   the newly booted system.

     When no options are given (i.e., RB_AUTOBOOT is used), the system is rebooted from file ``kernel'' in the root file system of unit 0 of a
     disk chosen in a processor specific way.  An automatic consistency check of the disks is normally performed (see fsck(8)).

RETURN VALUES

     If successful, this call never returns.  Otherwise, a -1 is returned and an error is returned in the global variable errno.

ERRORS

     [EPERM]		The caller is not the super-user.

SEE ALSO

     crash(8), halt(8), init(8), reboot(8), savecore(8)

HISTORY

     The reboot() system call appeared in 4.0BSD.

BUGS

     The HP300 implementation supports neither RB_DFLTROOT nor RB_KDB.

BSD
								   June 4, 1993 							       BSD