fmstat(1M) System Administration Commands fmstat(1M)
NAME
fmstat - report fault management module statistics
SYNOPSIS
fmstat [-asz] [-m module] [interval [count]]
DESCRIPTION
The fmstat utility can be used by administrators and service personnel to report statistics associated with the Solaris Fault Manager,
fmd(1M) and its associated set of modules. The Fault Manager runs in the background on each Solaris system. It receives telemetry informa-
tion relating to problems detected by the system software, diagnoses these problems, and initiates proactive self-healing activities such
as disabling faulty components.
You can use fmstat to view statistics for diagnosis engines and agents that are currently participating in fault management. The documenta-
tion for fmd(1M), fmadm(1M), and fmdump(1M) describes more about tools to observe fault management activities.
If the -m option is present, fmstat reports any statistics kept by the specified fault management module. The module list can be obtained
using fmadm config.
If the -m option is not present, fmstat reports the following statistics for each of its client modules:
module The name of the fault management module, as reported by fmadm config.
ev_recv The number of telemetry events received by the module.
ev_acpt The number of events accepted by the module as relevant to a diagnosis.
wait The average number of telemetry events waiting to be examined by the module.
svc_t The average service time for telemetry events received by the module, in milliseconds.
%w The percentage of time that there were telemetry events waiting to be examined by the module.
%b The percentage of time that the module was busy processing telemetry events.
open The number of active cases (open problem investigations) owned by the module.
solve The total number of cases solved by this module since it was loaded.
memsz The amount of dynamic memory currently allocated by this module.
bufsz The amount of persistent buffer space currently allocated by this module.
The fmstat utility requires the user to posses the SYS_CONFIG privilege. Refer to the System Administration Guide: Security Services for
more information about how to configure Solaris privileges.
OPTIONS
The following options are supported:
-a Print all statistics for a module, including those kept on its behalf by fmd. If the -a option is not present, only those
statistics kept by the module are reported. If the -a option is used without the -m module, a set of global statistics
associated with fmd are displayed.
-m module Print a report on the statistics associated with the specified fault management module, instead of the default statistics
report. Modules can publish an arbitrary set of statistics to help Sun service the fault management software itself. The
module statistics constitute a Private interface. See attributes(5) for information on Sun's rules for Private interfaces.
Scripts should not be written that depend upon the values of fault management module statistics as they can change without
notice.
-s Print a report on Soft Error Rate Discrimination (SERD) engines associated with the module instead of the default module
statistics report. A SERD engine is a construct used by fault management software to determine if a statistical threshold
measured as N events in some time T has been exceeded. The -s option can only be used in combination with the -m option.
-z Omit statistics with a zero value from the report associated with the specified fault management module. The -z option can
only be used in combination with the -m option.
OPERANDS
The following operands are supported:
count Print only count reports, and then exit.
interval Print a new report every interval seconds.
If no interval and no count are specified, a single report is printed and fmstat exits. If an interval is specified but no count is speci-
fied, fmstat prints reports every interval seconds indefinitely until the command is interrupted.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 A fatal error occurred. A fatal error could be the failure to communicate with fmd(1M). It could also be that insufficient privi-
leges were available to perform the requested operation.
2 Invalid command-line options were specified.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWfmd |
+-----------------------------+-----------------------------+
|Interface Stability |See below. |
+-----------------------------+-----------------------------+
The command-line options are Evolving. The human-readable default report is Unstable. The human-readable module report is Private.
SEE ALSO
fmadm(1M), fmd(1M), fmdump(1M), attributes(5)
System Administration Guide: Security Services
SunOS 5.10 8 Mar 2004 fmstat(1M)