send(3XNET) X/Open Networking Services Library Functions send(3XNET)
NAME
send - send a message on a socket
SYNOPSIS
cc [ flag ... ] file ... -lxnet [ library ... ]
#include <sys/socket.h>
ssize_t send(int socket, const void *buffer, size_t length, int flags);
PARAMETERS
socket Specifies the socket file descriptor.
buffer Points to the buffer containing the message to send.
length Specifies the length of the message in bytes.
flags Specifies the type of message transmission. Values of this argument are formed by logically OR'ing zero or more of the following
flags:
MSG_EOR Terminates a record (if supported by the protocol)
MSG_OOB Sends out-of-band data on sockets that support out-of-band communications. The significance and semantics of out-of-
band data are protocol-specific.
DESCRIPTION
The send() function initiates transmission of a message from the specified socket to its peer. The send() function sends a message only
when the socket is connected (including when the peer of a connectionless socket has been set via connect(3XNET)).
The length of the message to be sent is specified by the length argument. If the message is too long to pass through the underlying proto-
col, send() fails and no data is transmitted.
Successful completion of a call to send() does not guarantee delivery of the message. A return value of -1 indicates only locally-detected
errors.
If space is not available at the sending socket to hold the message to be transmitted and the socket file descriptor does not have O_NON-
BLOCK set, send() blocks until space is available. If space is not available at the sending socket to hold the message to be transmitted
and the socket file descriptor does have O_NONBLOCK set, send() will fail. The select(3C) and poll(2) functions can be used to determine
when it is possible to send more data.
The socket in use may require the process to have appropriate privileges to use the send() function.
USAGE
The send() function is identical to sendto(3XNET) with a null pointer dest_len argument, and to write() if no flags are used.
RETURN VALUES
Upon successful completion, send() returns the number of bytes sent. Otherwise, -1 is returned and errno is set to indicate the error.
ERRORS
The send() function will fail if:
EAGAIN The socket's file descriptor is marked O_NONBLOCK and the requested operation would block.
EWOULDBLOCK
EBADF The socket argument is not a valid file descriptor.
ECONNRESET A connection was forcibly closed by a peer.
EDESTADDRREQ The socket is not connection-mode and no peer address is set.
EFAULT The buffer parameter can not be accessed.
EINTR A signal interrupted send() before any data was transmitted.
EMSGSIZE The message is too large be sent all at once, as the socket requires.
ENOTCONN The socket is not connected or otherwise has not had the peer prespecified.
ENOTSOCK The socket argument does not refer to a socket.
EOPNOTSUPP The socket argument is associated with a socket that does not support one or more of the values set in flags.
EPIPE The socket is shut down for writing, or the socket is connection-mode and is no longer connected. In the latter case, and
if the socket is of type SOCK_STREAM, the SIGPIPE signal is generated to the calling thread.
The send() function may fail if:
EACCES The calling process does not have the appropriate privileges.
EIO An I/O error occurred while reading from or writing to the file system.
ENETDOWN The local interface used to reach the destination is down.
ENETUNREACH No route to the network is present.
ENOBUFS Insufficient resources were available in the system to perform the operation.
ENOSR There were insufficient STREAMS resources available for the operation to complete.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface Stability |Standard |
+-----------------------------+-----------------------------+
|MT-Level |MT-Safe |
+-----------------------------+-----------------------------+
SEE ALSO
connect(3XNET), getsockopt(3XNET), poll(2), recv(3XNET), recvfrom(3XNET), recvmsg(3XNET), select(3C), sendmsg(3XNET), sendto(3XNET), set-
sockopt(3XNET), shutdown(3XNET), socket(3XNET), attributes(5), standards(5)
SunOS 5.11 1 Nov 2003 send(3XNET)