Unix/Linux Go Back    


OpenDarwin 7.2.1 - man page for rmt (opendarwin section 8)

Linux & Unix Commands - Search Man Pages
Man Page or Keyword Search:   man
Select Man Page Set:       apropos Keyword Search (sections above)


RMT(8)				   BSD System Manager's Manual				   RMT(8)

NAME
     rmt -- remote magtape protocol module

SYNOPSIS
     rmt

DESCRIPTION
     rmt is a program used by the remote dump and restore programs in manipulating a magnetic
     tape drive through an interprocess communication connection.  rmt is normally started up
     with an rexec(3) or rcmd(3) call.

     The rmt program accepts requests specific to the manipulation of magnetic tapes, performs
     the commands, then responds with a status indication.  All responses are in ASCII and in one
     of two forms.  Successful commands have responses of:

	   Anumber\n

     Number is an ASCII representation of a decimal number.  Unsuccessful commands are responded
     to with:

	   Eerror-number\nerror-message\n

     Error-number is one of the possible error numbers described in intro(2) and error-message is
     the corresponding error string as printed from a call to perror(3).  The protocol is com-
     prised of the following commands, which are sent as indicated - no spaces are supplied
     between the command and its arguments, or between its arguments, and '\n' indicates that a
     newline should be supplied:

     Odevice\nmode\n
	     Open the specified deviceusing the indicated mode.Deviceis a full pathname and
	     modeis an ASCIIrepresentation of a decimal number suitable for passing to open(2).If
	     a device had already been opened, it is closed before a new open is performed.

     Cdevice\n
	     Close the currently open device.  The devicespecified is ignored.

     Loffset\nwhence\n
	     Perform an lseek(2) operation using the specified parameters.  The response value is
	     that returned from the lseek call.

     Wcount\n
	     Write data onto the open device.  rmt reads count bytes from the connection, abort-
	     ing if a premature end-of-file is encountered.  The response value is that returned
	     from the write(2) call.

     Rcount\n
	     Read count bytes of data from the open device.  If count exceeds the size of the
	     data buffer (10 kilobytes), it is truncated to the data buffer size.  rmt then per-
	     forms the requested read(2) and responds with Acount-read\n if the read was success-
	     ful; otherwise an error in the standard format is returned.  If the read was suc-
	     cessful, the data read is then sent.

     Ioperation\ncount\n
	     Perform a MTIOCOP ioctl(2) command using the specified parameters.  The parameters
	     are interpreted as the ASCII representations of the decimal values to place in the
	     mt_op and mt_count fields of the structure used in the ioctl call.  The return value
	     is the count parameter when the operation is successful.

     S	     Return the status of the open device, as obtained with a MTIOCGET ioctl call.  If
	     the operation was successful, an ``ack'' is sent with the size of the status buffer,
	     then the status buffer is sent (in binary).

     Any other command causes rmt to exit.

DIAGNOSTICS
     All responses are of the form described above.

SEE ALSO
     rcmd(3), rexec(3), mtio(4), rdump(8), rrestore(8)

BUGS
     People should be discouraged from using this for a remote file access protocol.

HISTORY
     The rmt command appeared in 4.2BSD.

4.2 Berkeley Distribution		   June 1, 1994 		4.2 Berkeley Distribution
Unix & Linux Commands & Man Pages : ©2000 - 2018 Unix and Linux Forums


All times are GMT -4. The time now is 06:01 PM.