MOVE_PAGES(2) Linux Programmer's Manual MOVE_PAGES(2)
move_pages - move individual pages of a process to another node
long move_pages(int pid, unsigned long count, void **pages,
const int *nodes, int *status, int flags);
Link with -lnuma.
move_pages() moves the specified pages of the process pid to the memory nodes specified by nodes. The result of the move is reflected in
status. The flags indicate constraints on the pages to be moved.
pid is the ID of the process in which pages are to be moved. If pid is 0, then move_pages() moves pages of the calling process.
To move pages in another process requires the following privileges:
* In kernels up to and including Linux 4.12: the caller must be privileged (CAP_SYS_NICE) or the real or effective user ID of the calling
process must match the real or saved-set user ID of the target process.
* The older rules allowed the caller to discover various virtual address choices made by the kernel that could lead to the defeat of
address-space-layout randomization for a process owned by the same UID as the caller, the rules were changed starting with Linux 4.13.
Since Linux 4.13, permission is governed by a ptrace access mode PTRACE_MODE_READ_REALCREDS check with respect to the target process;
count is the number of pages to move. It defines the size of the three arrays pages, nodes, and status.
pages is an array of pointers to the pages that should be moved. These are pointers that should be aligned to page boundaries. Addresses
are specified as seen by the process specified by pid.
nodes is an array of integers that specify the desired location for each page. Each element in the array is a node number. nodes can also
be NULL, in which case move_pages() does not move any pages but instead will return the node where each page currently resides, in the sta-
tus array. Obtaining the status of each page may be necessary to determine pages that need to be moved.
status is an array of integers that return the status of each page. The array contains valid values only if move_pages() did not return an
flags specify what types of pages to move. MPOL_MF_MOVE means that only pages that are in exclusive use by the process are to be moved.
MPOL_MF_MOVE_ALL means that pages shared between multiple processes can also be moved. The process must be privileged (CAP_SYS_NICE) to
Page states in the status array
The following values can be returned in each element of the status array.
Identifies the node on which the page resides.
The page is mapped by multiple processes and can be moved only if MPOL_MF_MOVE_ALL is specified.
-EBUSY The page is currently busy and cannot be moved. Try again later. This occurs if a page is undergoing I/O or another kernel subsys-
tem is holding a reference to the page.
This is a zero page or the memory area is not mapped by the process.
-EIO Unable to write back a page. The page has to be written back in order to move it since the page is dirty and the filesystem does
not provide a migration function that would allow the move of dirty pages.
A dirty page cannot be moved. The filesystem does not provide a migration function and has no ability to write back pages.
The page is not present.
Unable to allocate memory on target node.
On success move_pages() returns zero. On error, it returns -1, and sets errno to indicate the error.
E2BIG Too many pages to move.
EACCES One of the target nodes is not allowed by the current cpuset.
EFAULT Parameter array could not be accessed.
EINVAL Flags other than MPOL_MF_MOVE and MPOL_MF_MOVE_ALL was specified or an attempt was made to migrate pages of a kernel thread.
ENODEV One of the target nodes is not online.
ENOENT No pages were found that require moving. All pages are either already on the target node, not present, had an invalid address or
could not be moved because they were mapped by multiple processes.
EPERM The caller specified MPOL_MF_MOVE_ALL without sufficient privileges (CAP_SYS_NICE). Or, the caller attempted to move pages of a
process belonging to another user but did not have privilege to do so (CAP_SYS_NICE).
ESRCH Process does not exist.
move_pages() first appeared on Linux in version 2.6.18.
This system call is Linux-specific.
For information on library support, see numa(7).
Use get_mempolicy(2) with the MPOL_F_MEMS_ALLOWED flag to obtain the set of nodes that are allowed by the current cpuset. Note that this
information is subject to change at any time by manual or automatic reconfiguration of the cpuset.
Use of this function may result in pages whose location (node) violates the memory policy established for the specified addresses (See
mbind(2)) and/or the specified process (See set_mempolicy(2)). That is, memory policy does not constrain the destination nodes used by
The <numaif.h> header is not included with glibc, but requires installing libnuma-devel or a similar package.
get_mempolicy(2), mbind(2), set_mempolicy(2), numa(3), numa_maps(5), cpuset(7), numa(7), migratepages(8), numastat(8)
This page is part of release 4.15 of the Linux man-pages project. A description of the project, information about reporting bugs, and the
latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.
Linux 2017-09-15 MOVE_PAGES(2)