Unix/Linux Go Back    

OpenDarwin 7.2.1 - man page for rs (opendarwin section 1)

Linux & Unix Commands - Search Man Pages
Man Page or Keyword Search:   man
Select Man Page Set:       apropos Keyword Search (sections above)

RS(1)				   BSD General Commands Manual				    RS(1)

     rs -- reshape a data array

     rs [-[csCS][x] [kKgGw][N] tTeEnyjhHmz] [rows [cols]]

     The rs utility reads the standard input, interpreting each line as a row of blank-separated
     entries in an array, transforms the array according to the options, and writes it on the
     standard output.  With no arguments it transforms stream input into a columnar format conve-
     nient for terminal viewing.

     The shape of the input array is deduced from the number of lines and the number of columns
     on the first line.  If that shape is inconvenient, a more useful one might be obtained by
     skipping some of the input with the -k option.  Other options control interpretation of the
     input columns.

     The shape of the output array is influenced by the rows and cols specifications, which
     should be positive integers.  If only one of them is a positive integer, rs computes a value
     for the other which will accommodate all of the data.  When necessary, missing data are sup-
     plied in a manner specified by the options and surplus data are deleted.  There are options
     to control presentation of the output columns, including transposition of the rows and col-

     The following options are available:

     -cx     Input columns are delimited by the single character x.  A missing x is taken to be

     -sx     Like -c, but maximal strings of x are delimiters.

     -Cx     Output columns are delimited by the single character x.  A missing x is taken to be

     -Sx     Like -C, but padded strings of x are delimiters.

     -t      Fill in the rows of the output array using the columns of the input array, that is,
	     transpose the input while honoring any rows and cols specifications.

     -T      Print the pure transpose of the input, ignoring any rows or cols specification.

     -kN     Ignore the first N lines of input.

     -KN     Like -k, but print the ignored lines.

     -gN     The gutter width (inter-column space), normally 2, is taken to be N.

     -GN     The gutter width has N percent of the maximum column width added to it.

     -e      Consider each line of input as an array entry.

     -n      On lines having fewer entries than the first line, use null entries to pad out the
	     line.  Normally, missing entries are taken from the next line of input.

     -y      If there are too few entries to make up the output dimensions, pad the output by
	     recycling the input from the beginning.  Normally, the output is padded with blanks.

     -h      Print the shape of the input array and do nothing else.  The shape is just the num-
	     ber of lines and the number of entries on the first line.

     -H      Like -h, but also print the length of each line.

     -j      Right adjust entries within columns.

     -wN     The width of the display, normally 80, is taken to be the positive integer N.

     -m      Do not trim excess delimiters from the ends of the output array.

     -z      Adapt column widths to fit the largest entries appearing in them.

     With no arguments, rs transposes its input, and assumes one array entry per input line
     unless the first non-ignored line is longer than the display width.  Option letters which
     take numerical arguments interpret a missing number as zero unless otherwise indicated.

     The rs utility can be used as a filter to convert the stream output of certain programs
     (e.g., spell, du, file, look, nm, who, and wc(1)) into a convenient ``window'' format, as in

	   % who | rs

     This function has been incorporated into the ls(1) program, though for most programs with
     similar output rs suffices.

     To convert stream input into vector output and back again, use

	   % rs 1 0 | rs 0 1

     A 10 by 10 array of random numbers from 1 to 100 and its transpose can be generated with

	   % jot -r 100 | rs 10 10 | tee array | rs -T > tarray

     In the editor vi(1), a file consisting of a multi-line vector with 9 elements per line can
     undergo insertions and deletions, and then be neatly reshaped into 9 columns with

	   :1,$!rs 0 9

     Finally, to sort a database by the first line of each 4-line field, try

	   % rs -eC 0 4 | sort | rs -c 0 1

     jot(1), pr(1), sort(1), vi(1)

     Handles only two dimensional arrays.

     The algorithm currently reads the whole file into memory, so files that do not fit in memory
     will not be reshaped.

     Fields cannot be defined yet on character positions.

     Re-ordering of columns is not yet possible.

     There are too many options.

BSD					December 30, 1993				      BSD
Unix & Linux Commands & Man Pages : ©2000 - 2018 Unix and Linux Forums

All times are GMT -4. The time now is 04:46 PM.