Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

nisopaccess(1) [opendarwin man page]

nisopaccess(1)							   User Commands						    nisopaccess(1)

NAME
nisopaccess - NIS+ operation access control administration command SYNOPSIS
nisopaccess [-v] directory operation rights nisopaccess [-v] [-r] directory operation nisopaccess [-v] [-l] directory [operation] DESCRIPTION
Most NIS+ operations have implied access control through the permissions on the objects that they manipulate. For example, in order to read an entry in a table, you must have read permission on that entry. However, some NIS+ operations by default perform no access checking at all and are allowed to all: Operation Example of commands that use the operation NIS_CHECKPOINT nisping -C NIS_CPTIME nisping, rpc.nisd NIS_MKDIR nismkdir NIS_PING nisping, rpc.nisd NIS_RMDIR nisrmdir NIS_SERVSTATE nisbackup, nisrestore NIS_STATUS nisstat, rpc.nispasswdd The nisopaccess command can be used to enforce access control on these operations on a per NIS+ directory basis. The directory argument should be the fully qualified name, including the trailing dot, of the NIS+ directory to which nisopaccess will be applied. As a short-hand method, if the directory name does not end in a trailing dot, for example "org_dir", then the domain name is appended. The domain name is also appended to partial paths such as "org_dir.xyz". You can use upper or lower case for the operation argument. However, you cannot mix cases. The "NIS_" prefix may be omitted. For example, NIS_PING can be specified as NIS_PING, nis_ping, PING, or ping. The rights argument is specified in the format defined by the nischmod(1) command. Since only the read ("r") rights are used to determine who has the right to perform the operation, the modify and delete rights may be used to control who can change access to the operation. The access checking performed for each operation is as follows. When an operation requires access be checked on all directories served by its rpc.nisd(1M), access is denied if even one of the directories prohibits the operation. NIS_CHECKPOINT Check specified directory, or all directories if there is no directory argument, as is the case when NIS_CHECKPOINT is issued by the "nisping -Ca" command. Return NIS_PERMISSION when access is denied. NIS_CPTIME Check specified directory. It returns 0 when access is denied. NIS_MKDIR Check parent of specified directory. Returns NIS_PERMISSION when access is denied. If the parent directory is not available locally, that is, it is not served by this rpc.nisd(1M), NIS_MKDIR access is allowed, though the operation will be executed only if this rpc.nisd is a known replica of the directory. You should note that the NIS_MKDIR operation does not create a NIS+ directory; it adds a directory to the serving list for this rpc.nisd, if appropriate. NIS_PING Check specified directory. No return value. NIS_RMDIR Check specified directory. NIS_PERMISSION is returned when access denied. The NIS_RMDIR operation does not remove a NIS+ directory; it deletes the directory from the serving list for this rpc.nisd, if appropriate. NIS_SERVSTATE Check access on all directories served by this rpc.nisd. If access is denied for a tag, "<permission denied>" is returned instead of the tag value. NIS_STATUS Same as for NIS_SERVSTATE. Notice that older clients may not supply authentication information for some of the operations listed above. These clients are treated as "nobody" when access checking is performed. The access control is implemented by creating a NIS+ table called "proto_op_access" in each NIS+ directory to which access control should be applied. The table can be manipulated using normal NIS+ commands. However, nisopaccess is the only supported interface for NIS+ opera- tion access control. OPTIONS
The following options are supported: -l List the access control for a single operation, or for all operations that have access control enabled. -r Remove access control for a certain operation on the specified directory. -v Verbose mode. EXAMPLES
Example 1: Enabling Access Control for the NIS_PING Operation To enable access control for the NIS_PING operation on "org_dir.`domainname`." such that only the owner of the directory can perform a NIS_PING, or change the NIS_PING rights: example% nisopaccess org_dir NIS_PING o=rmcd,g=,w=,n= Example 2: Listing the Access to NIS_PING To list the access to the NIS_PING operation for org_dir: example% nisopaccess -l org_dir NIS_PING NIS_PING ----rmcd-------- owner.dom.ain. group.dom.ain. Example 3: Removing Access Control for NIS_PING To remove access control for NIS_PING on org_dir: example% nisopaccess -r org_dir NIS_PING EXIT STATUS
The following exit values are returned: 0 Successful operation. other Operation failed. The status is usually the return status from a NIS+ command such as nistbladm. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWnisu | +-----------------------------+-----------------------------+ SEE ALSO
nis+(1), nischmod(1), nistbladm(1), rpc.nisd(1M), attributes(5) NOTES
NIS+ might not be supported in future releases of the SolarisTM Operating Environment. Tools to aid the migration from NIS+ to LDAP are available in the Solaris 9 operating environment. For more information, visit http://www.sun.com/directory/nisplus/transition.html. SunOS 5.10 10 Dec 2001 nisopaccess(1)
Man Page