USBHID-UPS(8) NUT Manual USBHID-UPS(8)
usbhid-ups - Driver for USB/HID UPS equipment
This man page only documents the hardware-specific features of the usbhid-ups driver. For information about the core driver, see
This driver, formerly called newhidups, replaces the legacy hidups driver, which only supported Linux systems.
usbhid-ups brings USB/HID UPS monitoring to NUT on all platform supporting USB through libusb. It should detect any UPS that uses the HID
power device class, but the amount of data will vary depending on the manufacturer and model.
At the present time, usbhid-ups supports:
o the newer Eaton USB models,
o all MGE USB models,
o all Dell USB models,
o some APC models,
o some Belkin models,
o some Cyber Power Systems models.
o some TrippLite models
For a more complete list, refer to the NUT hardware compatibility list, available in the source distribution as data/drivers.list, or on
the NUT website. You may use the "explore" driver option to gather information from HID UPSes which are not yet supported; see below for
This driver is known to work on:
o most Linux systems,
o FreeBSD (beta stage) and maybe other *BSD,
o Darwin / Mac OS X,
o Solaris 10.
This driver also supports the following optional settings:
Set the timer before the UPS is turned off after the kill power command is sent (via the -k switch).
The default value is 20 (in seconds). Usually this must be lower than ondelay, but the driver will not warn you upon startup if it
Set the timer for the UPS to switch on in case the power returns after the kill power command had been sent but before the actual
switch off. This ensures the machines connected to the UPS are, in all cases, rebooted after a power failure.
The default value is 30 (in seconds). Usually this must be greater than offdelay, but the driver will not warn you upon startup if it
isn't. Some UPS'es will restart no matter what, even if the power is (still) out at the moment this timer elapses. In that case, you
could try if setting ondelay = -1 in ups.conf helps.
Set polling frequency, in seconds, to reduce the USB data flow. Between two polling requests, the driver will wait for interrupts (aka
UPS notifications), which are data changes returned by the UPS by itself. This mechanism allow to avoid or reduce staleness message,
due to the UPS being temporarily overloaded with too much polling requests. The default value is 30 (in seconds).
If this flag is set, the driver will ignore interrupts it receives from the UPS (not recommended, but needed if these reports are
broken on your UPS).
vendor=regex, product=regex, serial=regex, vendorid=regex, productid=regex
Select a specific UPS, in case there is more than one connected via USB Each option specifies an extended regular expression (see
regex(7)) that must match the UPS's entire vendor/product/serial string (minus any surrounding whitespace), or the whole 4-digit
hexadecimal code for vendorid and productid. Try -DD for finding out the strings to match.
o -x vendor="Foo.Corporation.*"
o -x vendorid=051d* (APC)
o -x product=".*(Smart|Back)-?UPS.*"
Select a UPS on a specific USB bus or group of busses. The argument is a regular expression that must match the bus name where the UPS
is connected (e.g. bus="002", bus="00[2-3]").
With this option, the driver will connect to any device, including ones that are not yet supported. This must always be combined with
the "vendorid" option. In this mode, the driver will not do anything useful except for printing debugging information (typically used
This driver is not built by default. You can build it by using "configure --with-usb=yes". Note that it will also install other USB
You also need to install manually the legacy hotplug files (libhidups and libhid.usermap, generally in /etc/hotplug/usb/), or the udev file
(nut-usbups.rules, generally in /etc/udev/rules.d/) to address the permission settings problem. For more information, refer to the README
file in nut/scripts/hotplug or nut/scripts/udev.
On Linux with MGE equipment, you will need at least a 2.4.25 or 2.6.2 kernel as well as libusb-0.1.8 or later to disable hiddev support and
The driver ignores the "port" value in ups.conf. Unlike previous versions of this driver, it is now possible to control multiple UPS units
simultaneously with this driver, provided they can be distinguished by setting some combination of the "vendor", "product", "serial",
"vendorid", and "productid" options. For instance:
driver = usbhid-ups
port = auto
vendorid = 0463
driver = usbhid-ups
port = auto
vendorid = 09ae
KNOWN ISSUES AND BUGS
Repetitive timeout and staleness
Some models tends to be unresponsive with the default polling frequency. The result is that your system log will have lots of messages
usb 2-1: control timeout on ep0in
usb 2-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 128 rq 6 len 256
In this case, simply modify the general parameter "pollinterval" to a higher value (like 10 for 10 seconds). This should solve the issue.
Got EPERM: Operation not permitted upon driver startup
You have forgotten to install the hotplug files, as explained in the INSTALLATION section above. Don't forget to restart hotplug so that it
applies these changes.
The hardware which was used for development of this driver is almost certainly different from what you have, and not all manufacturers
follow the USB HID Power Device Class specifications to the letter. You don't want to find out that yours has issues here when a power
failure hits your server room and you're not around to manually restart your servers.
If you rely on the UPS to shutdown your systems in case of mains failure and to restart them when the power returns, you must test this.
You can do so by running upsmon -c fsd. With the mains present, this should bring your systems down and then cycle the power to restart
them again. If you do the same without mains present, it should do the same, but in this case, the outputs shall remain off until mains
power is applied again.
Originally sponsored by MGE UPS SYSTEMS. Now sponsored by Eaton http://opensource.eaton.com Arnaud Quette, Peter Selinger, Arjen de Korte
The core driver
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 USBHID-UPS(8)