SOCKD.ROUTE(5) File Formats Manual SOCKD.ROUTE(5)
NAME
sockd.route - Route file for multi-homed SOCKS proxy server
SYNOPSIS
/etc/sockd.route
DESCRIPTION
The file /etc/sockd.route is used by the SOCKS server program sockd to determine which of its network interfaces it should use to reach a
given destination host. It is needed only if your SOCKS server host is multi-homed and your version of sockd supports RBIND. A multi-homed
host is a host with more than one network interfaces and with its IP_FORWARDING turned off. Only the multi-homed version of sockd can be
run on such hosts. You can find out the version of your sockd (or rsockd) by command
sockd -ver
or
rsockd -ver
A line in the file can be up to 1024 characters long. Lines starting with a `#' are comments. Non-comment lines must be of the form
if_addr dst_addr dst_mask
All three fields are required and are separated by spaces or tabs. Each filed is specified in the usual dotted form of IP addresses, e.g.,
128.23.16.2. if_addr must be the IP address of one of the network interfaces on the SOCKS server host. dst_addr specifies either the IP
address of a host, a network, or a subnet in the usual dotted form, e.g., 129.201.4.0, or a domain name, e.g., internic.net. dst_mask spec-
ifies mask for the IP address used in dst_addr. Bits in dst_mask that are set to 0 indicate the bit positions to be ignored during compar-
ison of IP addresses. So, specifying 255.255.255.255 in dst_mask demands an exact match with dst_addr, whereas 0.0.0.0 in dst_mask causes a
matching with any given destination address regardless of what is specified for dst_addr. If a domain name is used for dst_addr, the con-
tents of dst_mask are ignored, though it must still be supplied (simply use 0.0.0.0). If the domain name starts with a period, it speci-
fies a zone and matches all domain names within that zone, otherwise it matches only the domain name itself. For example, xyz.com matches
only xyz.comP, while .xyz.com macthes not only xyz.com, but also abc.xyz.com and this.and.that.xyz.com, among others. The special symbol
ALL (which must be entirely in uppercase) matches everything. Domain names are otherwise case-insentive.
When using a domain name in dst_addr, you have be very careful in maintaining your DNS setup. See the last few paragraphs in sockd.conf(5).
When a multi-homed sockd receives a network request, it first checks with /etc/sockd.fc (or /etc/sockd.conf) to decide whether the request
should be allowed or denied. For an allowable request, sockd then checks the given destination IP address or domain name against the
dst_addr dst_mask pair in /etc/sockd.route, one line at a line. Once a match is found, the network interface of the corresponding if_addr
field is used for connection to the destination host. Remaining lines in the file are skipped. Therefore the order of the lines in the
file is of extreme importance. If no match is found throughout the file, a line indicating the error is produced using syslog with facility
daemon and level err and the request is ignored.
You have the option of using the frozen route file /etc/sockd.fr instead of /etc/sockd.route. The frosen file is produced by make_sockdfr
and is essentially the memory image of the parsed route file. Using it can reduce the start-up delay of the SOCKS server since it eliminate
the need for parsing. Since the SOCKS server always looks for /etc/sockd.fr first, be sure that you always run make_sockdfr every time
after you modifify /etc/sockd.route.
EXAMPLES
Suppose you have a dual-homed host with interface 129.1.2.3 connecting to your internal Class B network 129.1, and interface 129.1.254.1
connecting to the outside world. If you only use the SOCKS server to provide connections to outside hosts, then the file /etc/sockd.route
only needs one line:
129.1.254.1 0.0.0.0 0.0.0.0
If you also use the SOCKS server to provide connection to internal hosts as well, then two lines would suffice:
129.1.2.3 129.1.0.0 255.255.0.0
129.1.254.1 0.0.0.0 0.0.0.0
Note that these two lines must be in the order given above.
If you prefer using domain name instead, the lines should be
129.1.2.3 .myown.com 0.0.0.0
129.1.254.1 0.0.0.0 0.0.0.0
assuming that myown.com is your domain.
SEE ALSO
dump_sockdfr(8), make_sockdfr(8), sockd(8), sockd.fr(5)
May 6, 1996 SOCKD.ROUTE(5)