WL(4) BSD/i386 Kernel Interfaces Manual WL(4)
NAME
wl -- T1 speed ISA/radio lan card
SYNOPSIS
device wl0 at isa? port 0x300 irq 5
DESCRIPTION
The wl driver controls a radio lan card system made originally by NCR, then ATT, now Lucent. The system is spread-spectrum radio at around
915 MHz (or 2.4 GHz). With the supplied omni-directional antennae, about 400 feet (indoors, more outdoors) can be covered in circumference.
This card can talk to the companion (wlp0) pccard. Speeds vary from 1 megabit to theoretically 2 megabits (roughly T1 in speed).
The card has three fundamental hardware units, a so-called PSA or programmable storage area, a radio modem, and a Ethernet lan controller.
The latter component is the ancient (and not very honorable) Intel 82586 Ethernet chip. Fundamentally it appears to the operating system as
an Ethernet system, and speaks IEEE MAC addresses. The radio modem simply translates Ethernet packets to/from radio packets, that are either
at 2.4 GHz or 915 MHz depending on the radio modem. It supports a collision avoidance scheme. The lan controller supports promiscuous mode,
broadcast, and multicasting (although there is a glitch in the latter). "It thinks it is Ethernet".
How it is used depends on the kind of antennae deployed with it. Point to point applications are possible as are Ethernet-like lan use. The
vendor ships an omni-directional antennae that works in the vicinity of 400 feet (indoors). Point to point antennae can be purchased that
will go miles.
SETUP
The card can either be initialized with the vendor supplied DOS setup software. Typically minimally an IRQ, port, and Network ID must be
supplied. Michael Smith's wlconfig(8) utility can now be used to do this work from the UNIX side. The card is "not" plug and play. The
network id controls whether one set of cards can hear another. If different, cards will read physical packets, but they will be discarded by
the radio modem.
CONTROL
In addition to the config utility, there are several sysctl switches that can be used to modify runtime parameters. The sysctl(8) variables
are as follows:
machdep.wl_xmit_delay <useconds> This variable will cause the driver to insert a delay on transmit. 250 is the default. The delay should
probably be a bit longer on faster cpus and less on slower cpus. It exists because the 82586 was not designed to work with Pentium-speed cpu
systems and if overdriven will have copious xmit side errors.
machdep.wl_ignore_nwid <0 | 1> This switch defaults to 0; i.e., the nwid is not ignored. It can be set to 1 to cause the nwid to not be
used. This may be useful when the device is in promiscuous mode as one can watch for all packets and ignore nwid differences.
machdep.wl_xmit_watch <milliseconds> This switch is not currently useful.
machdep.wl_gather_snr <milliseconds> This switch is not currently useful.
There is also a signal strength cache in the driver. It may be interrogated with wlconfig(8). Incoming packets are checked for certain
hardware radio-modem values including signal strength, silence, and quality, which range fro 0..63, 0..63, and 0..15 respectively. Thus one
can read out signal strenth values to see how close/far peer nodes are. The signal strength cache is indexed by sender MAC address. There
are two sysctls that change how it filters packets. Both are on by default.
machdep.wl_wlcache_mcastonly <0 | 1> By default this switch is on. It forces the cache to filter out unicast packets. Only broadcast or
multicast packets are accepted.
machdep.wl_wlcache_iponly <0 | 1> By default this switch is on. It forces the driver to discard non-IP packets and also stores the IP src
address. ARP packets are ignored, as are any other network protocol barring IPv4 packets.
CAVEATS
The 82586 has numerous defects. It may experience transmit-side errors when modern faster cpus send packets at it faster than it can handle.
The driver (and probably the chip) does not support an all multicast mode. As a result, it can be used with applications like mrouted(8)
(ports/net/mrouted), but it must go into promiscuous mode for that to work. The driver is slow to change modes from "normal" to promiscuous
mode, presumably due to delays in the configuration code.
SEE ALSO
sysctl(8), wlconfig(8)
http://www.wavelan.com
HISTORY
The wl driver was written by Anders Klemets (thousands of years ago?) and appears to be based on an even older Intel 82586 driver. The 82586
controller was one of the first (if not the first?) integrated lan controller on the block. That does not mean it was the best either.
Anders ported and or created a driver for the ISA wavelan and PCCARD wavelan system too (wlp). Robert T. Morris, Jr. ported the Mach drivers
to BSDI. Jim Binkley ported them to FreeBSD 2.1. Michael Smith ported the wl driver only to 2.2.2. Jim and Michael have been maintaining
them. The current state of the driver is NOT ANYONE'S FAULT. Thanks to Bernie Doehner and Robert Buaas for contributions.
AUTHORS
Too numerous to mention. See above.
BSD September 29, 2006 BSD