Visit The New, Modern Unix Linux Community

Linux and UNIX Man Pages

Test Your Knowledge in Computers #493
Difficulty: Medium
When a program executes, each command executes one after the other, top-to-bottom. This is known as inconsequential control flow.
True or False?
Linux & Unix Commands - Search Man Pages

uvscom(4) [freebsd man page]

UVSCOM(4)						   BSD Kernel Interfaces Manual 						 UVSCOM(4)

NAME
uvscom -- USB support for SUNTAC Slipper U VS-10U serial adapters driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device usb device ucom device uvscom Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): uvscom_load="YES" HARDWARE
The uvscom driver supports the following adapters: o DDI Pocket Air H" C@rd o DDI Pocket Air H" C@rd 64 o NTT P-in o NTT P-in m@ster DESCRIPTION
The uvscom driver provides support for the SUNTAC Slipper U VS-10U chip. Slipper U is a PC Card to USB converter for data communication card adapters. The device is accessed through the ucom(4) driver which makes it behave like a tty(4). SEE ALSO
tty(4), ucom(4), usb(4) HISTORY
The uvscom driver first appeared in FreeBSD and later in NetBSD 1.6. This manual page was adopted from NetBSD by Tom Rhodes <trhodes@FreeBSD.org> in April 2002. BSD
November 20, 2011 BSD

Check Out this Related Man Page

UVSCOM(4)						   BSD Kernel Interfaces Manual 						 UVSCOM(4)

NAME
uvscom -- USB support for SUNTAC Slipper U VS-10U serial adapters driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device uvscom device ucom Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): uvscom_load="YES" HARDWARE
The uvscom driver supports the following adapters: o DDI Pocket Air H" C@rd o DDI Pocket Air H" C@rd 64 o NTT P-in o NTT P-in m@ster DESCRIPTION
The uvscom driver provides support for the SUNTAC Slipper U VS-10U chip. Slipper U is a PC Card to USB converter for data communication card adapters. The device is accessed through the ucom(4) driver which makes it behave like a tty(4). SEE ALSO
tty(4), ucom(4), usb(4) HISTORY
The uvscom driver first appeared in FreeBSD and later in NetBSD 1.6. This manual page was adopted from NetBSD by Tom Rhodes <trhodes@FreeBSD.org> in April 2002. BSD
November 22, 2006 BSD

3 More Discussions You Might Find Interesting

1. What is on Your Mind?

MacBook Air Anyone?

I am thinking to purchase a new MacBook Air, 13 inch. Anyone have a MacBook Air? What do you think about it? Seems expensive, a bit. Is it worth it? (9 Replies)
Discussion started by: Neo
9 Replies

2. Ubuntu

Kernel panics : trying to write / read on tiny tty driver

I'm a beginner to the Linux programming and trying my hands on some device driver examples while practising. The below code (a trimmed down version of tiny_tty.c from ldd3 book) loads perfectly using insmod and I'm able to see it in /proc/tty/drivers , /proc/modules and device nodes are getting... (1 Reply)
Discussion started by: diwsdiwa
1 Replies

3. UNIX for Dummies Questions & Answers

Get a data and save

If I have a A.log 1 Air Flow Monitor : 34.070 Degrees C 2 Air Flow Monitor : 41.730 Degrees C 3 Air Flow Monitor : 35.340 Degrees C 4 Air Flow Monitor : 33.370 Degrees C 5 Air Flow Monitor : 36.770 Degrees C 6 Air Flow Monitor : 45.910 Degrees C 7 Air Flow Monitor ... (1 Reply)
Discussion started by: sabercats
1 Replies

Featured Tech Videos