uvisor(4) [freebsd man page]

UVISOR(4)						   BSD Kernel Interfaces Manual 						 UVISOR(4)

NAME

     uvisor -- USB support for the PalmOS based PDAs

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device usb
	   device ucom
	   device uvisor

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   uvisor_load="YES"

DESCRIPTION

     The uvisor driver provides support for USB based PalmOS PDAs, like Handspring Visor, Palm Mxxx series, and Sony Clie.

     The device is accessed through the ucom(4) driver which makes it behave like a tty(4).  The device has several ports for different purposes,
     each of them gets its own ucom(4) device.	The attach message describes the purpose of each port.

     The usual Pilot tools can be used to access the attached device on the HotSync port.

HARDWARE

     The uvisor driver supports the following devices:

     o	 Aceeca Mez1000 RDA
     o	 Handspring Treo
     o	 Handspring Treo 600
     o	 Handspring Visor
     o	 Palm I705
     o	 Palm M125
     o	 Palm M130
     o	 Palm M500
     o	 Palm M505
     o	 Palm M515
     o	 Palm Tungsten T
     o	 Palm Tungsten Z
     o	 Palm Zire
     o	 Palm Zire 31
     o	 Sony Clie 4.0
     o	 Sony Clie 4.1
     o	 Sony Clie 5.0
     o	 Sony Clie PEG-S500C
     o	 Sony Clie NX60
     o	 Sony Clie S360
     o	 Sony Clie TJ37

SEE ALSO

     tty(4), ucom(4), usb(4)

HISTORY

     The uvisor driver was adopted from NetBSD 1.5 in August 2002.  This manual page was adopted from NetBSD by Tom Rhodes <trhodes@FreeBSD.org>
     at that time.

BUGS

     The code to provide multiple ucom(4) instances has not yet been ported from NetBSD.  It is unclear whether this driver works in its current
     state.

BSD
								 November 20, 2011							       BSD

UFOMA(4)						   BSD Kernel Interfaces Manual 						  UFOMA(4)

NAME

     ufoma -- USB mobile phone support

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device usb
	   device ucom
	   device ufoma

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   ufoma_load="YES"

DESCRIPTION

     The ufoma driver provides support for USB mobile phone terminals in the subset of the Mobile Computing Promotion Consortium USB Implementa-
     tion Guideline, which is adopted by FOMA, the NTT DoCoMo 3G system, terminal.  These are partly like CDC ACM model based modems, which are
     supported by umodem(4), but the ufoma driver recognizes a specific USB descriptor that describes its role and interface structure, and it
     will negotiate its role when the device is open.  They support a regular AT command set and the commands can either be multiplexed with the
     data stream or handled through separate pipes.  In the latter case the AT commands have to be given on a device separate from the data
     device.

     The device is accessed through the ucom(4) driver which makes it behave like a tty(4).

SYSCTLS

     These devices often have a few interface sets and these interfaces have their role, sometimes multiplexed.  These roles are identified with
     the following sysctl MIBs:

     dev.ucom.%d.supportmode
	     The modes which are supported by the interface.

     dev.ucom.%d.currentmode
	     Current mode of the interface.

     dev.ucom.%d.openmode
	     Mode to transit when the device is open next.
     The modes are as follows:

     modem   Accepts AT commands and go and pass packet communication data.

     handsfree
	     Accepts AT commands but it does not pass data.

     obex    Accepts OBEX frame which is used to exchange telephone book, etc.

     vendor1, vendor2
	     Vendor specific data may be passed.

     deactivated
	     When an interface is recognized by the system but not used, the interface will be set to this mode.

     unlinked
	     When an interface is not yet negotiated, the interface is in this mode.

HARDWARE

     Devices supported by the ufoma driver include:

     o	 SHARP FOMA SH902i
     o	 KYOCERA PHS AH-K3001V (a.k.a Kyopon)
     o	 SANYO Vodafone3G V801SA

SEE ALSO

     Specification can be found at:

     http://www.nttdocomo.co.jp/corporate/technology/document/foma/index.html
     http://www.mcpc-jp.org/doclist.htm

     tty(4), ucom(4), umodem(4), usb(4)

HISTORY

     The ufoma driver appeared in FreeBSD 7.0, partly derived from the umodem(4) code.

BUGS

     Interfaces with multiplexed commands and data and interfaces with commands only are supported.

BSD
								 November 20, 2011							       BSD