Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

pcib(4) [freebsd man page]

PCIB(4) 						   BSD Kernel Interfaces Manual 						   PCIB(4)

NAME
pcib -- PCI bridge driver SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file: device pci DESCRIPTION
The pcib driver provides for host and PCI bridges in a PCI system. BUGS
This man page is too short. BSD
January 18, 2008 BSD

Check Out this Related Man Page

XPCI(4) 						 BSD/xen Kernel Interfaces Manual						   XPCI(4)

NAME
xpci -- Xen frontend paravirtualized PCI pass-through driver SYNOPSIS
xpci* at xenbus? pci* at xpci? DESCRIPTION
The xpci driver is the frontend part of the PCI pass-through functionality that can be used by Xen guest domains to communicate with PCI devices. From a guest point of view, xpci is similar to a pci(4) bus, except that the guest talks with the PCI backend driver instead of the real physical device directly. When the host domain is NetBSD, the xpci driver is backed by a pciback(4) driver within the dom0. SEE ALSO
pci(4), pciback(4), xenbus(4) HISTORY
The xpci driver first appeared in NetBSD 5.1. AUTHORS
The xpci driver was written by Manuel Bouyer <bouyer@NetBSD.org>. SECURITY CONSIDERATIONS
As PCI passthrough offers the possibility for guest domains to send arbitrary PCI commands to a physical device, this has direct impact on the overall stability and security of the system. For example, in case of erroneous or malicious commands, the device could overwrite physi- cal memory portions, via DMA. BSD
January 8, 2011 BSD
Man Page

11 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network down when visitors are over 300

Hi, there. Recently one of my friends used FreeBSD 4.8 to setup a web server, and the network connection is 100MB/s. But every time when the visitors approached 300 people, the network turned so slow, and eventually "dead". Why is that? And how should we solve this problem. I don't know what... (7 Replies)
Discussion started by: HOUSCOUS
7 Replies

2. BSD

Floppy drive problem.

My FreeBSD install at ad0s1, and Windows 2000 at ad2s1. Everytime I start my FreeBSD, it shows me this message: fdc0: cmd 3 failed at out byte 1 of 3 pmtimer 0 on isa0 fdc0: cannot reserve I/O port range (6 ports) My Floppy drive info: 0x03F2 - 0x03F3 0x03F4 - 0x03F5 0x03F7 - 0x03F7... (6 Replies)
Discussion started by: _cs
6 Replies

3. UNIX for Advanced & Expert Users

OpenBSD bad Multitasking?

Hi! Ive been following a OpenBSD thread from Dec 2003 "Issues multitasking during disk IO", and no "good" answer has still been given. I experience the same problems as he did. But ill explain my problem below for you who doesnt want to read a hole new thread. First off, i been using OpenBSD... (2 Replies)
Discussion started by: Tomtefan
2 Replies

4. Solaris

How to get Solaris 8 x86 (32 bits) ethernet up on Vmware 6.x.x?

Hello professional, I am using Solaris 8 x86 (32 bits) running on Vmware 6.x.x my vmware configuration: config.version = "8" virtualHW.version = "6" scsi0.present = "TRUE" memsize = "1024" ide0:0.present = "TRUE" ide0:0.fileName = "Other.vmdk" ide1:0.present = "TRUE"... (0 Replies)
Discussion started by: draggy
0 Replies

5. UNIX for Dummies Questions & Answers

SoundCard.. Again

Hi everyone.I have an Audigy2 ZS sound card. I'm not a guru so don't send me faraway)) Well my card sounds only in front channels... can't setup 5.1. and i can't made a microphone works. PS: A have red this Yuriy Tsibizov (AKA chibis) many time. Here is some system info dmesg Copyright... (0 Replies)
Discussion started by: Levenson
0 Replies

6. Solaris

How to Configure a Static Ip Address

Hello friend, I am new in UNIX, but I want to learn a lot Well I have a problem to try to configure my PC with a static IP Address (IP 192.168.1.39, Mask 255.255.255.0, gateway 192.168.1.1) (DNS 200.48.225.130 and 200.48.225.146). where are the file that I must be change? The SO is Sun Solaris... (15 Replies)
Discussion started by: andresguillen
15 Replies

7. Solaris

Sun Fire V490 occasionally downs

I can't find why but I suppose it is because of some hardware failures... I have a Sun Fire V490 with Solaris 10 5/08 which runs Sun Cluster 3.2 and it downs occasionally with a circumstances I can't define... Also I note some strange behavior after server failures: when I ran any diagnostics from... (6 Replies)
Discussion started by: Sapfeer
6 Replies

8. Solaris

Error while installing zoning

hi all, i am configure zone according to this steps and i face this error could you please help to solv it poolcfg -c 'create pset weblogic1-pset (uint pset.min=1; uint pset.max=1)' poolcfg -c 'create pool weblogic1-pool' poolcfg -c 'associate pool weblogic1-pool (pset weblogic1-pset)' ... (5 Replies)
Discussion started by: jamisux
5 Replies

9. Solaris

How to install PGX32 on Sparc 10 Ultra?

I'm trying to install a PGX32 video card on my Sparc 10 Ultra running Solaris 10. I've got the Oracle installation guide for it and I got as far as: "4. Insert the CD-ROM labeled “GFX OpenWindows for Solaris 2” into the drive." I don't have a CD-ROM by that name and a web search for that... (21 Replies)
Discussion started by: Michele31416
21 Replies

10. Solaris

Machine is not booting

Dear all Any help would be greatly appreciated, I have Solaris 10 installed on an M5000 SPARC machine. While rebooting it, we are faced with the following message then the OK prompt: SPARC Enterprise M5000 Server, using Domain console Copyright (c) 1998, 2010, Oracle and/or its affiliates. All... (25 Replies)
Discussion started by: abohmeed
25 Replies

11. Solaris

Sun enterprise 420R boot issue

Hi, I am using sun enterprise 420R server. Problem is on the monitor i am not able to see anything. I tried Serial connection, on terminal(using serial) i could see that POST(power on start tests) tests are being done, after that "timeout waiting for arp rarp packet" message keep displaying... (11 Replies)
Discussion started by: kkittu009
11 Replies