OHCI(4) BSD Kernel Interfaces Manual OHCI(4)NAME
ohci -- OHCI USB Host Controller driver
The ohci driver provides support for OHCI-type PCI based USB controllers.
The ohci driver supports all OHCI v1.0 compliant controllers including:
o AcerLabs M5237 (Aladdin-V)
o OPTi 82C861 (FireLink)
o NEC uPD 9210
o CMD Tech 670 (USB0670)
o CMD Tech 673 (USB0673)
o NVIDIA nForce3
o Sun PCIO-2 (RIO USB)
SEE ALSO ehci(4), uhci(4), xhci(4)HISTORY
The ohci device driver first appeared in FreeBSD 3.0.
The ohci driver was written by Lennart Augustsson <email@example.com> for the NetBSD project.
BSD June 23, 2005 BSD
Check Out this Related Man Page
EHCI(4) BSD Kernel Interfaces Manual EHCI(4)NAME
ehci -- USB Enhanced Host Controller driver
The ehci driver provides support for the USB Enhanced Host Controller Interface, which is used by USB 2.0 controllers.
EHCI controllers are peculiar in that they can only handle the USB 2.0 protocol. This means that they normally have one or more companion
controllers (i.e., ohci(4) or uhci(4)) handling USB 1.x devices. Consequently each USB connector is electrically connected to two USB con-
trollers. The handling of this is totally automatic, but can be noticed since USB 1.x and USB 2.0 devices plugged in to the same connector
appear to connect to different USB busses.
SEE ALSO ohci(4), uhci(4), usb(4)HISTORY
The ehci device driver first appeared in FreeBSD 5.1.
The driver is not finished and is quite buggy.
There is currently no support for isochronous transfers.
BSD March 20, 2005 BSD
I have a program that logs serial port data. In order to do so it requires the full device name in linux (e.g. /dev/ttyUSB0) and a baudrate.
Does anyone know how I can find out the device name in the terminal? I am trying to port this application to Android and cant figure it out.
... (22 Replies)
I'm a new user of this forum and I'm not an expert of linux.
I have a broken old pc with red hat linux, I clone hdd to another pc with different mainboard and it's ok but it has only one problem, the usb ports not work.
In the boot this message appears:
... (9 Replies)
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
The organization I work for uses SCOM(Microsoft Systems Center Operations Manager) for Data Center Management/alerting. Since the client was installed on our Linux servers we have been getting messages from SCOM stating "DPC Time Percentage is too high". This is happening on all our... (0 Replies)
2 things then I'll post my problem. Don't you find it very odd that in the "linux" sub-forum, they don't list any linux O.S.'s. This should've been posted in 'emergencies", but it refused!!!??
I'm at wit's end. Been fighting LinuxMint 17 for about 2 months now and it's... (3 Replies)
i have a system with 6 sata3 seagate st3000dm01 disks running on stable Debian with software raid mdadm. i have md0 for root and md1 for swap and md2 for the files. i now want to add one more disk = sdh4 for md2 but i got this errors:
The new disk is connected to an 4 port sata... (7 Replies)
I have a T2000 enterprise SPARC server that's no longer on contract with Oracle. It's on old firmware (6.3.x). After a power-down this weekend, it won't boot normally. Boot snapshot at the bottom of the post.
It can boot to cdrom, and it'll boot to failsafe mode, but it won't do a regular... (9 Replies)
I have the following cenario:
I have requested a LUN from the NetApp to create a file system, and the netapp admin provide me with one as you can see below, but after following all the steps, I could not create a file system on the device:
Searching for disks...done
... (11 Replies)
I am familiar with Linux, FreeBSD, but relatively new to Solaris. Because I wanted to play a little with servers and networks, I got a used SunFire v20z with AMD Opteron processors and installed OpenIndiana 151a8 on top of that. This is the first machine of this kind I have ever... (1 Reply)
i have 2 machines in ESXI6 that both made a restart at the same time but no errors from ESXI side.
one machine with Centos 6.6 and one with centos 7
same log at the Dmesg:
please help me find a lead what could made this ?
Mar 17 20:20:28 pbxnl-b-sales-ru-ua init: tty (/dev/tty1) main... (2 Replies)
I'm find out a way to disable the DGD: AMD Radeon HD 7470M on my Ubutu 16.04.2 LTS because radeon open source module is not capable to support this GPU and consequence the boot is very slow.
I have tried serveral way with pci-stub.ids in the grub menu but not work.
In general how... (11 Replies)
I have an Siemens IoT2020 with a Sim7000e cellular board that I connect via USB to the board and connect to Telstra Cat-M1 network.
I can send and receive SMS and do so using Node-Red but can also do with Minicom etc. When connected I get :
root@iot2000:~# dmesg | grep USB
ACPI:... (0 Replies)
I'm a little embarrassed after all these years I've never really successfully compiled my own kernel. I used this guide to make the following files:
When I first booted into this... (4 Replies)