Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

ipw(4) [freebsd man page]

IPW(4)							   BSD Kernel Interfaces Manual 						    IPW(4)

NAME
ipw -- Intel PRO/Wireless 2100 IEEE 802.11 driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device ipw device ipwfw device pci device wlan device firmware Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_ipw_load="YES" In both cases, place the following line in loader.conf(5) to acknowledge the firmware license (see below): legal.intel_ipw.license_ack=1 DESCRIPTION
The ipw driver provides support for the Intel PRO/Wireless 2100 MiniPCI network adapter. ipw supports station, adhoc, and monitor mode oper- ation. Only one virtual interface may be configured at any time. For more information on configuring this device, see ifconfig(8). This driver requires the firmware built with the ipwfw module to work. For the loaded firmware to be enabled for use the license at /usr/share/doc/legal/intel_ipw/LICENSE must be agreed by adding the following line to loader.conf(5): legal.intel_ipw.license_ack=1 FILES
/usr/share/doc/legal/intel_ipw/LICENSE ipw firmware license EXAMPLES
Join an existing BSS network (i.e., connect to an access point): ifconfig wlan create wlandev ipw0 inet 192.168.0.20 netmask 0xffffff00 Join a specific BSS network with network name ``my_net'': ifconfig wlan create wlandev ipw0 ssid my_net up Join a specific BSS network with 64-bit WEP encryption: ifconfig wlan create wlandev ipw0 ssid my_net wepmode on wepkey 0x1234567890 weptxkey 1 up Join a specific BSS network with 128-bit WEP encryption: ifconfig wlan create wlandev ipw0 wlanmode adhoc ssid my_net wepmode on wepkey 0x01020304050607080910111213 weptxkey 1 DIAGNOSTICS
ipw%d: device timeout The driver will reset the hardware. This should not happen. ipw%d: firmware error The onboard microcontroller crashes for some reason. The driver will reset the hardware. This should not happen. ipw%d: timeout waiting for firmware initialization to complete The onboard microcontroller failed to initialize in time. This should not happen. ipw%d: could not load firmware image '%s' The driver failed to load the firmware image using the firmware(9) subsystem. Verify the ipwfw(4) firmware module is installed and the license agreement loader(8) tunable has been set. ipw%d: could not load microcode An attempt to upload the microcode image to the onboard microcontroller failed. This should not happen. ipw%d: could not load firmware An attempt to upload the firmware image to the onboard microcontroller failed. This should not happen. SEE ALSO
ipwfw(4), pci(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8) AUTHORS
The original ipw driver was written by Damien Bergamini <damien.bergamini@free.fr>. BSD
April 13, 2008 BSD

Check Out this Related Man Page

IPW(4)							   BSD Kernel Interfaces Manual 						    IPW(4)

NAME
ipw -- Intel PRO/Wireless 2100 IEEE 802.11 driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device ipw device ipwfw device pci device wlan device firmware Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_ipw_load="YES" In both cases, place the following line in loader.conf(5) to acknowledge the firmware license (see below): legal.intel_ipw.license_ack=1 DESCRIPTION
The ipw driver provides support for the Intel PRO/Wireless 2100 MiniPCI network adapter. ipw supports station, adhoc, and monitor mode oper- ation. Only one virtual interface may be configured at any time. For more information on configuring this device, see ifconfig(8). This driver requires the firmware built with the ipwfw module to work. For the loaded firmware to be enabled for use the license at /usr/share/doc/legal/intel_ipw/LICENSE must be agreed by adding the following line to loader.conf(5): legal.intel_ipw.license_ack=1 FILES
/usr/share/doc/legal/intel_ipw/LICENSE ipw firmware license EXAMPLES
Join an existing BSS network (i.e., connect to an access point): ifconfig wlan create wlandev ipw0 inet 192.168.0.20 netmask 0xffffff00 Join a specific BSS network with network name ``my_net'': ifconfig wlan create wlandev ipw0 ssid my_net up Join a specific BSS network with 64-bit WEP encryption: ifconfig wlan create wlandev ipw0 ssid my_net wepmode on wepkey 0x1234567890 weptxkey 1 up Join a specific BSS network with 128-bit WEP encryption: ifconfig wlan create wlandev ipw0 wlanmode adhoc ssid my_net wepmode on wepkey 0x01020304050607080910111213 weptxkey 1 DIAGNOSTICS
ipw%d: device timeout The driver will reset the hardware. This should not happen. ipw%d: firmware error The onboard microcontroller crashes for some reason. The driver will reset the hardware. This should not happen. ipw%d: timeout waiting for firmware initialization to complete The onboard microcontroller failed to initialize in time. This should not happen. ipw%d: could not load firmware image '%s' The driver failed to load the firmware image using the firmware(9) subsystem. Verify the ipwfw(4) firmware module is installed and the license agreement loader(8) tunable has been set. ipw%d: could not load microcode An attempt to upload the microcode image to the onboard microcontroller failed. This should not happen. ipw%d: could not load firmware An attempt to upload the firmware image to the onboard microcontroller failed. This should not happen. SEE ALSO
ipwfw(4), pci(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8) AUTHORS
The original ipw driver was written by Damien Bergamini <damien.bergamini@free.fr>. BSD
April 13, 2008 BSD
Man Page