MADVISE(2) BSD System Calls Manual MADVISE(2)
madvise, posix_madvise -- give advice about use of memory
Standard C Library (libc, -lc)
madvise(void *addr, size_t len, int behav);
posix_madvise(void *addr, size_t len, int behav);
The madvise() system call allows a process that has knowledge of its memory behavior to describe it to the system. The posix_madvise()
interface is identical, except it returns an error number on error and does not modify errno, and is provided for standards conformance.
The known behaviors are:
MADV_NORMAL Tells the system to revert to the default paging behavior.
MADV_RANDOM Is a hint that pages will be accessed randomly, and prefetching is likely not advantageous.
MADV_SEQUENTIAL Causes the VM system to depress the priority of pages immediately preceding a given page when it is faulted in.
MADV_WILLNEED Causes pages that are in a given virtual address range to temporarily have higher priority, and if they are in memory,
decrease the likelihood of them being freed. Additionally, the pages that are already in memory will be immediately mapped
into the process, thereby eliminating unnecessary overhead of going through the entire process of faulting the pages in.
This WILL NOT fault pages in from backing store, but quickly map the pages already in memory into the calling process.
MADV_DONTNEED Allows the VM system to decrease the in-memory priority of pages in the specified range. Additionally future references to
this address range will incur a page fault.
MADV_FREE Gives the VM system the freedom to free pages, and tells the system that information in the specified page range is no
longer important. This is an efficient way of allowing malloc(3) to free pages anywhere in the address space, while keeping
the address space valid. The next time that the page is referenced, the page might be demand zeroed, or might contain the
data that was there before the MADV_FREE call. References made to that address space range will not make the VM system page
the information back in from backing store until the page is modified again.
MADV_NOSYNC Request that the system not flush the data associated with this map to physical backing store unless it needs to. Typically
this prevents the file system update daemon from gratuitously writing pages dirtied by the VM system to physical disk. Note
that VM/file system coherency is always maintained, this feature simply ensures that the mapped data is only flush when it
needs to be, usually by the system pager.
This feature is typically used when you want to use a file-backed shared memory area to communicate between processes (IPC)
and do not particularly need the data being stored in that area to be physically written to disk. With this feature you get
the equivalent performance with mmap that you would expect to get with SysV shared memory calls, but in a more controllable
and less restrictive manner. However, note that this feature is not portable across UNIX platforms (though some may do the
right thing by default). For more information see the MAP_NOSYNC section of mmap(2)
MADV_AUTOSYNC Undoes the effects of MADV_NOSYNC for any future pages dirtied within the address range. The effect on pages already dirt-
ied is indeterminate - they may or may not be reverted. You can guarantee reversion by using the msync(2) or fsync(2) sys-
MADV_NOCORE Region is not included in a core file.
MADV_CORE Include region in a core file.
MADV_PROTECT Informs the VM system this process should not be killed when the swap space is exhausted. The process must have superuser
privileges. This should be used judiciously in processes that must remain running for the system to properly function.
Portable programs that call the posix_madvise() interface should use the aliases POSIX_MADV_NORMAL, POSIX_MADV_SEQUENTIAL, POSIX_MADV_RANDOM,
POSIX_MADV_WILLNEED, and POSIX_MADV_DONTNEED rather than the flags described above.
The madvise() function returns the value 0 if successful; otherwise the value -1 is returned and the global variable errno is set to indicate
The madvise() system call will fail if:
[EINVAL] The behav argument is not valid.
[ENOMEM] The virtual address range specified by the addr and len arguments is not valid.
[EPERM] MADV_PROTECT was specified and the process does not have superuser privileges.
mincore(2), mprotect(2), msync(2), munmap(2), posix_fadvise(2)
The posix_madvise() interface conforms to IEEE Std 1003.1-2001 (``POSIX.1'').
The madvise() system call first appeared in 4.4BSD.
January 30, 2014 BSD