BUS_SETUP_INTR(9) BSD Kernel Developer's Manual BUS_SETUP_INTR(9)
BUS_SETUP_INTR, bus_setup_intr, BUS_TEARDOWN_INTR, bus_teardown_intr -- create, attach and teardown an interrupt handler
BUS_SETUP_INTR(device_t dev, device_t child, struct resource *irq, int flags, driver_filter_t *filter, driver_intr_t *ithread, void *arg,
bus_setup_intr(device_t dev, struct resource *r, int flags, driver_filter_t filter, driver_intr_t ithread, void *arg, void **cookiep);
BUS_TEARDOWN_INTR(device_t dev, device_t child, struct resource *irq, void *cookiep);
bus_teardown_intr(device_t dev, struct resource *r, void *cookiep);
The BUS_SETUP_INTR() method will create and attach an interrupt handler to an interrupt previously allocated by the resource manager's
BUS_ALLOC_RESOURCE(9) method. The flags are found in <sys/bus.h>, and give the broad category of interrupt. The flags also tell the inter-
rupt handlers about certain device driver characteristics. INTR_EXCL marks the handler as being an exclusive handler for this interrupt.
INTR_MPSAFE tells the scheduler that the interrupt handler is well behaved in a preemptive environment (``SMP safe''), and does not need to
be protected by the ``Giant Lock'' mutex. INTR_ENTROPY marks the interrupt as being a good source of entropy - this may be used by the
entropy device /dev/random.
To define a time-critical handler (previously known as INTR_FAST) that will not execute any potentially blocking operation, use the filter
argument. See the Filter Routines section below for information on writing a filter. Otherwise, use the ithread argument. The defined han-
dler will be called with the value arg as its only argument. See the ithread Routines section below for more information on writing an
The cookiep argument is a pointer to a void * that BUS_SETUP_INTR() will write a cookie for the parent bus' use to if it is successful in
establishing an interrupt. Driver writers may assume that this cookie will be non-zero. The nexus driver will write 0 on failure to
The interrupt handler will be detached by BUS_TEARDOWN_INTR(). The cookie needs to be passed to BUS_TEARDOWN_INTR() in order to tear down
the correct interrupt handler. Once BUS_TEARDOWN_INTR() returns, it is guaranteed that the interrupt function is not active and will no
longer be called.
Mutexes are not allowed to be held across calls to these functions.
A filter runs in a context very similar to what was known as an INTR_FAST routine in previous versions of FreeBSD. In this context, normal
mutexes cannot be used. Only the spin lock version of these can be used (specified by passing MTX_SPIN to mtx_init() when initializing the
mutex). wakeup(9) and similar routines can be called. Atomic operations from machine/atomic may be used. Reads and writes to hardware
through bus_space(9) may be used. PCI configuration registers may be read and written. All other kernel interfaces cannot be used.
In this restricted environment, care must be taken to account for all races. A careful analysis of races should be done as well. It is gen-
erally cheaper to take an extra interrupt, for example, than to protect variables with spinlocks. Read, modify, write cycles of hardware
registers need to be carefully analyzed if other threads are accessing the same registers.
Generally, a filter routine will use one of two strategies. The first strategy is to simply mask the interrupt in hardware and allow the
ithread routine to read the state from the hardware and then reenable interrupts. The ithread also acknowledges the interrupt before re-
enabling the interrupt source in hardware. Most PCI hardware can mask its interrupt source.
The second common approach is to use a filter with multiple taskqueue(9) tasks. In this case, the filter acknowledges the interrupts and
queues the work to the appropriate taskqueue. Where one has to multiplex different kinds of interrupt sources, like a network card's trans-
mit and receive paths, this can reduce lock contention and increase performance.
You should not malloc(9) from inside a filter. You may not call anything that uses a normal mutex. Witness may complain about these.
You can do whatever you want in an ithread routine, except sleep. Care must be taken not to sleep in an ithread. In addition, one should
minimize lock contention in an ithread routine because contested locks ripple over to all other ithread routines on that interrupt.
Sleeping is voluntarily giving up control of your thread. All the sleep routine found in msleep(9) sleep. Waiting for a condition variable
described in condvar(9) is sleeping. Calling any function that does any of these things is sleeping.
Zero is returned on success, otherwise an appropriate error is returned.
random(4), device(9), driver(9), mtx_init(9), wakeup(9)
This manual page was written by Jeroen Ruigrok van der Werven <asmodai@FreeBSD.org> based on the manual pages for BUS_CREATE_INTR() and
BUS_CONNECT_INTR() written by Doug Rabson <dfr@FreeBSD.org>.
December 18, 2007 BSD