TTYLOG(8)TTYLOG(8)NAME
ttylog - serial device logger
DESCRIPTION
This program writes everything comes from a serial device from /dev/tty* onto stdout. You can specify device and baud rate of the device.
OPTIONS
ttylog follows the GNU command line syntax.
-h, --help
Displays a little help
-v, --version
Version number of ttylog
-b, --baud
Baud rate of the device. Available baud rates: 300, 1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200
-d --device
The serial device. For example /dev/ttyS1
AUTHOR
This manual page was originally written by Tibor Koleszar <t.koleszar@somogy.hu>, for the Debian GNU/Linux system. Modifications and
updates written by Robert James Clay <jame@rocasa.us>.
2010-03-23 TTYLOG(8)
Check Out this Related Man Page
ace(7) Miscellaneous Information Manual ace(7)NAME
ace - Serial communications interface
SYNOPSIS
controller ace0 at * slot ? vector aceintr
DESCRIPTION
The ace serial line controller provides a serial communications interface on DEC 2000, AlphaStation, and AlphaServer platforms. The serial
communications ports that are controlled by ace adhere to the RS-232 standard and can operate at rates from 50 to 115200 baud (see tty(7)).
These communications ports support serial-line printers, modems, and terminals.
In alternate console configurations (that is, no graphics head), the terminal to be the system console must be connected to the port that
is mapped to /dev/tty00. (See ports(7) for information about mapping AlphaStation and AlphaServer port labels to device pathnames.) Cur-
rently, some processors that use the ace driver limit the serial console port to 9600 baud, 8-bit, no parity and no modem support. However,
some processor consoles do support baud rates other than 9600 baud and allow the use of modems as console devices. Consult your hardware
documentation to determine the type of console support your system provides.
The driver for the ace interface supports hardware flow control using the Request to Send (RTS) and Clear to Send (CTS) signals. When
hardware flow control is enabled, the flow of input data is controlled by the RTS signal and the flow of output data is controlled by the
CTS signal. If the CTS signal is off, the driver suspends output to that line until the CTS lead is reasserted. Likewise the driver turns
off the RTS lead to tell the device connected to the line to stop sending data as a result of congestion on the host side. When the condi-
tion clears, the driver turns on the RTS lead to tell the device to resume sending data.
The DCD (carrier detect) timer value defaults to 2 seconds. This value may be changed if your modem hardware requires a different value.
the change can be made in the /etc/sysconfigtab file as follows:
ace: dcd_timer=n
where n is the time interval in seconds, and can be set to 0 (no timeout), 1, or 2 seconds. Alternatively, you can use the sysconfig com-
mand to set the same time interval option as follows:
# sysconfig -r ace dcd_timer=[n]
If you use the sysconfig command, the value will not be preserved when the system is rebooted. To preserve the setting, put the entry in
the /etc/sysconfigtab file
NOTES
If you are using the alternate system console to perform kernel debugging, you must change the kdebug entry in the /etc/remote file to use
/dev/tty01; when the kernel is running in debugging mode, no other application can use the port. See Kernel Debugging for information on
setting up your system for kernel debugging.
RESTRICTIONS
Unless alternative specifications are stated in your system hardware documentation, data communications equipment attached to the console
serial port in alternate console configurations must be set to 9600 baud, 8-bits, no parity. If a serial console is being used, /dev/tty00
cannot be opened by another process. The ace driver enforces this restriction.
Baud rates greater than 38400 are not supported on the two primary serial ports on the DEC 2000 system. However, if you use an ISA serial
or modem card that is capable of communicating at the higher rates, the higher rates are supported.
FILES
console terminal local terminal local terminal
RELATED INFORMATION MAKEDEV(8), console(7), devio(7), modem(7), ports(7), tty(7)
Kernel Debugging
System Administration delim off
ace(7)