starfire-diag(8) [debian man page]
STARFIRE-DIAG(8) System Manager's Manual STARFIRE-DIAG(8) NAME
starfire-diag - EEPROM setup and diagnostic program for ethernet cards based on the Adaptec 6915 "Starfire" chip. SYNOPSIS
starfire-diag [options] DESCRIPTION
starfire-diag is a program that you can use to diagnose problems with Adaptec 6915 "Starfire" ethernet cards. OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. -h, --help Show summary of options. -V, --version Show version of program. -v, --verbose Verbose mode. -q, --quiet Be very unverbose. -# <cardnum> Use card number <cardnum>. -a, --show_all_registers Print all registers. -e, --show-eeprom Dump EEPROM contents to stdout. -E, --emergency-rewrite Re-write a corrupted EEPROM. -p, --base-address <port> Specify port to use. -A, --Advertise <mediaype> Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD. -F, --new-interface <interface> Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx, 100baseFx-FDX, MII and Autosense. -H, --new-hwaddress <address> Set card to a new hardware address. -m, --show-mii Dump MII management registers. -R, --reset Reset the transceiver. -T, --test Do register and SRAM test. -w, --write-EEPROM <values> Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do! -f, --force-detection Try to identify the card, even if it is active. -t, --chip-type <card> Explicitly set the chip. To get all valid numbers, run starfire-diag with the options '-t -1'. SEE ALSO
mii-diag(8) AUTHOR
starfire-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others). February 18, 2002 STARFIRE-DIAG(8)
Check Out this Related Man Page
RTL8139-DIAG(8) System Manager's Manual RTL8139-DIAG(8) NAME
rtl8139-diag - EEPROM setup and diagnostic program for ethernet cards based on the Realtek 8129 and 8139 chips. SYNOPSIS
rtl8139-diag [options] DESCRIPTION
rtl8139-diag is a program that you can use to diagnose problems with ethernet cards based on the Realtek 8129 or 8139 chip series. OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is included below. -h, --help Show summary of options. -V, --version Show version of program. -v, --verbose Verbose mode. -q, --quiet Be very unverbose. -# <cardnum> Use card number <cardnum>. -a, --show_all_registers Print all registers. -e, --show-eeprom Dump EEPROM contents to stdout. -E, --emergency-rewrite Re-write a corrupted EEPROM. -p, --base-address <port> Specify port to use. -A, --Advertise <mediaype> Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD. -F, --new-interface <interface> Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx, 100baseFx-FDX, MII, Autosense and Autonegotiate. -H, --new-hwaddress <address> Set card to a new hardware address. -m, --show-mii Dump MII management registers. -R, --reset Reset the transceiver. -T, --test Do register and SRAM test. -w, --write-EEPROM <values> Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do! -f, --force-detection Try to identify the card, even if it is active. -t, --chip-type <card> Explicitly set the chip. To get all valid numbers, run rtl8139-diag with the options '-t -1'. SEE ALSO
mii-diag(8) AUTHOR
rtl8139-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others). February 18, 2002 RTL8139-DIAG(8)