vga_setmode(3) Svgalib User Manual vga_setmode(3)
vga_setmode - sets a video mode
int vga_setmode(int mode);
vga_setmode(int mode) selects the video mode given and clears the screen (if it was a graphics mode). Basically this should be the first
action of your application after calling vga_init(3) and finding out which mode to use. Prior to exiting your application should call
vga_setmode() returns 0 on success and -1 if this mode is not available.
From svgalib-1.4.1, if mode is -1 then vga_setmode() returns the current svgalib version, in BCD format, so svgalib 1.4.1 returns 0x1410.
mode should be one of the following, predefined values, or generally a value in range 1 <= mode <= vga_lastmodenumber() where vga_mode-
info(3) returned details about this mode. Instead of trying to set the mode, vga_hasmode(3) determines if the mode would actually be sup-
ported. It is also possible to use the numeric values given below though this is discouraged. They are commonly used as values for the
SVGALIB_DEFAULT_MODE environment variable to set the vga_getdefaultmode(3).
Here are the predefined values for mode.
TEXT(0) restores textmode and falls back to ordinary text console handling. All other calls switch to a graphics mode. You should set this
mode prior to exiting an svgalib application.
VGA compatible graphics modes
In general, for all modes following, the first number is the amount of x pixels, the second the amount of y pixels, the third the number of
colors, with shortcuts 32K, 64K, 16M, 16M4 for 32768, 65536, and 1677721. Those with 2 or more than 256 colors use fixed color mappings
(either black and white or some RGB true/high color) the others make use of a color lookup table.
Memory layout for the VGA modes is weird. Too weird to be explained here, but you can check the usual VGA literature. vga_setmodeX(3) has
a short explanation which is valid for all 256 color modes.
G320x200x16(1), G640x200x16(2), G640x350x16(3), G640x480x16(4), G320x200x256(5), G320x240x256(6), G320x400x256(7), G360x480x256(8), and
Basic SVGA modes
These use linear 256 color memory layouts similar to G320x200x256.
G640x480x256(10), G800x600x256(11), G1024x768x256(12), and G1280x1024x256(13)
High color SVGA modes
These also use linear memory layouts, but for 32K & 64K each pixel occupies two bytes and three for 16M. For 32K, each 16 bit word is
divided into 555 bit portions refering to 5 bit red, green, blue part. The most significant bit is ignored by the card. For 64K the divi-
sion is 565 allowing to specify green in a little bit more detail (Human eyes are more sensitive to green. People joke this is because our
ancestors lived in trees where light was filtered through green leaves).
For the 16M modes, from low to high addresses the 3 bytes are named BGR and specify the blue, green, red parts of the pixel value.
G320x200x32K(14), G320x200x64K(15), G320x200x16M(16), G640x480x32K(17), G640x480x64K(18), G640x480x16M(19), G800x600x32K(20),
G800x600x64K(21), G800x600x16M(22), G1024x768x32K(23), G1024x768x64K(24), G1024x768x16M(25), G1280x1024x32K(26), G1280x1024x64K(27), and
High resolutions with less color numbers.
Memory layout is probably one nibble per pixel, two pixels per byte in a linear fashion where the most significant nibble is the left most
G800x600x16(29), G1024x768x16(30), and G1280x1024x16(31)
Hercules emulation mode
Again check out the ordinary VGA literature for the memory layout.
32-bit per pixel modes
These are similar to 16M but each pixel uses four bytes. The first three are similar to 16M but the fourth is left empty and ignored by the
VGA card (you can store own status there).
This eases pixel address calculations on the screen and drawing operations. However, 1/3 more data has to be moved to the screen. Experi-
ments show that usually the higher memory bandwidth used outweighs the effects of the simplified algorithms by far.
G320x200x16M32(33), G640x480x16M32(34), G800x600x16M32(35), G1024x768x16M32(36), and G1280x1024x16M32(37)
Some more resolutions
It should by now be clear how the modes will look.
G1152x864x16(38), G1152x864x256(39), G1152x864x32K(40), G1152x864x64K(41), G1152x864x16M(42), G1152x864x16M32(43), G1600x1200x16(44),
G1600x1200x256(45), G1600x1200x32K(46), G1600x1200x64K(47), G1600x1200x16M(48), and G1600x1200x16M32(49)
The vgatest(6) produces a list of supported modes for your hardware, prints some info on the modes and allows you to try each of them.
svgalib(7), vgagl(7), libvga.config(5), vgatest(6), vga_hasmode(3), vga_init(3), vga_modeinfo(3), vga_getcurrentmode(3), vga_getdefault-
mode(3), vga_lastmodenumber(3), vga_getmodename(3), vga_getmodenumber(3)
This manual page was edited by Michael Weller <firstname.lastname@example.org>. The exact source of the referenced function as well as of the
original documentation is unknown.
It is very likely that both are at least to some extent are due to Harm Hanemaayer <H.Hanemaayer@inter.nl.net>.
Occasionally this might be wrong. I hereby asked to be excused by the original author and will happily accept any additions or corrections
to this first version of the svgalib manual.
Svgalib 1.4.1 28 Jul 1999 vga_setmode(3)