NCPLOGIN(1) BSD General Commands Manual NCPLOGIN(1)
ncplogin -- create permanent connection to a NetWare server
ncplogin [-BCDN] [-S server] [-U user] [-A host] [-I level] [-M mode] [-O [owner][:group]] [-R retrycount] [-T tree] [-W timeout]
ncplogin [-BCDN] [-A host] [-I level] [-M mode] [-O [owner][:group]] [-R retrycount] [-T tree] [-W timeout] /server:user
Connections to a NetWare server can be created and used independently of the mount_nwfs(8) command. Connections can be created by any user.
Each user can have multiple connections, but each NetWareServer:NetWareUser pair should be unique.
The ncplogin command is used to create a permanent connection to a NetWare server. Permanent connections will stay open even if no applica-
tion uses them. This allows users to run different ncp* programs without specifying a file server and user to use. Established connections
can be destroyed with the ncplogout(1) command.
Upper case options described in this manual page are common for other ncp* programs and are referred to as ``connection options''. Options
-U and -S are mutually exclusive with the /server:user syntax.
The following options are available:
Specify the name of the NetWare server to connect to. This affects only IPX servers. For servers supporting IP natively, see the -A
Specify the name of the user used in the login sequence.
Use the UDP protocol to connect to a NetWare 5.x server specified by the host argument.
-C Do not convert the password to uppercase.
-D Mark the connection as primary. The option can be used to modify existing connections. Only the ncplogin program accepts this
Try to use signature_level. Available values are:
0 disable signatures
1 enable (use if required by server)
2 request but do not require signing
3 require signatures
Note that only packet header signing is implemented.
Share this connection. The bits in the mode argument are similar to standard file permissions:
4 (READ) connection will be visible.
2 (WRITE) connection can be closed/modified.
1 (EXECUTE) user is allowed to execute requests.
By default, the connection is created with mode 0700 and only the owner can use it. Specifying 0750 as the argument to the -M option
would allow read-only group access as well. This would allow the group to perform NCP requests, but not to destroy the connection.
When a server is not explicitly specified, ncp* programs try to find a suitable connection in the following order:
1. Try to find a connection owned by the user. If there is more than one such connection, try to determine which one is pri-
mary. (The primary flag is set with the -D option.)
2. If the primary connection could not be determined, the first shared connection will be used.
-N Do not prompt for a password. At run time, ncplogin reads the ~/.nwfsrc file for additional configuration parameters and a password.
If no password is found for the specified server:user pair, ncplogin prompts for it.
-O Specify the owner and group attributes for the connection. By default, newly created connections take the owner attribute from the
creating user's username and the group attribute from the creating user's primary group. This option overrides that behaviour. Only
the superuser can override the owner attribute for a connection.
-P Mark the connection as permanent. The ncplogin utility always creates permanent connections. This option can be useful in other
Specify the number of retries to be performed before dropping the connection. The default value is 10.
Note: after a connection is marked ``BAD'', each request will try to restore it. This process restores only the NCP connection; it
does not reopen any files that were open at the time that the connection was marked ``BAD''.
Specify the server request timeout in seconds. The default is 5 seconds.
This syntax is provided for the sake of simplicity and is mutually exclusive with the -S and -U options.
Low-level connection management is implemented in the ncp.ko kernel module. The IPXrouted(8) program is also required for IPX support.
~/.nwfsrc keeps static parameters for connections and other information; see /usr/share/examples/nwclient/dot.nwfsrc for details.
The ncplogin command first appeared in FreeBSD 4.0.
Boris Popov <email@example.com>, <firstname.lastname@example.org>
Please report any bugs to the author.
September 15, 1999 BSD