cdvdcontrol(1) cdvdcontrol 1.4 Manual cdvdcontrol(1)
cdvdcontrol - Tool to get full control on your Plextor optical device
cdvdcontrol [-d DEVICE] [OPTION]
pxcontrol gives you access on all features that are supported by your Plextor drive. This tool is what you want, when you use optical
devices which were manufactured by Plextor.
-l scan busses for all available optical devices
cdvdcontrol supports the following features: AutoStrategy, BitSetting, DiagnoseMode, GigaRec, Hide-CDR, MediaLock, PlexEraser, PoweRec,
SecuRec, SilentMode, SingleSession, Simulation, SpeedRead and VariRec.
The available features depend on your drive. Take a look at http://www.plextor.com or simply read the glossar on:
http://qpxtool.sourceforge.net/glossar.html to see supported features.
can be an IDE, SCSI, SATA, USB or FireWire connected optical drive. Not all SATA controller support all Plextor features.
/dev/hdX: IDE device
/dev/scdX: Linux 2.4: SATA, SCSI, USB device, or IDE device via ide-scsi emulation
/dev/srX: Linux 2.6: IDE device via new ATA layer, SCSI or USB device
/dev/cd: SCSI device
/dev/acd: ATA device
C:,D:,E:, ... X:,Y:,Z:
AutoStrategy (AS) is a Feature to determine a writing strategy for an inserted empty DVD media. Writing strategies are saved in the
AutoStrategy DataBase (ASDB). This command needs a specified DEVICE.
select the AutoStrategy mode
auto drive selects the strategy from the ASDB or from
the firmware. If there is no entry available, a
new one is created.
forced creates a new ASDB entry, even if there is already
one available in the ASDB.
on an existing AS from the DB is used. If there is no
entry, the strategy from the firmware is used.
off only strategy from the firmware is used. If there
is no entry available, the default strategy is used.
--as-list view complete ASDB list.
activate ASDB entry number X (value between 1-10).
deactivate ASDB entry number X (value between 1-10).
delete ASDB entry number X (value between 1-10).
remove all ASDB entries form the ASDB.
creates an AS database entry.
Mode should be combination if [q|f] and [a|r]
q quick AS creating.
f full AS creating. Media is written.
a AS is appended to the list in the ASDB.
r AS entry replaces relying ASDB entry.
load an ASDB from a file.
save ASDB into file. For PX-755/PX-760 only!
PX-755 export maybe buggy.
due to some compatibility problems of some DVD readers, it could make sense to use BitSetting, which sets the Booktype of media to DVD-ROM.
This OPTION requiers a specified DEVIVE.
enable / disable Bitsetting for DVD+R.
on defines DVD+R as DVD-ROM media.
off keeps DVD+R media as what it is.
enable / disable Bitsetting for DVD+R DL.
on define DVD+R DL media as DVD-ROM media.
off keeps DVD+R DL media as what it is.
are OPTIONS to detect the drive itself, the current settings and the available features.
-c, --current show current status of selected DEVICE.
-h, --help show help.
-l, --scan search all busses and list detected drives.
-s, --supported show features supported by selected DEVICE.
-v show output in verbose mode.
Increase (higher value) or Decrease (lower value) the regular capacity, which can be written on CD media. Ejecting the disc results in
flushing the GigaRec settings. Buffer UnderrunProof is disabled while GigaRec is active. The recording speed is limited to 4x or 8x DAO.
Use cdrdao or cdrskin for writing media with GigaRec function. Otherwise if you use cdrecord your values are flushed. GigaRec settings need
a specified DEVICE.
set GigaRec to <state>, which is a value in the
range of 0.6, 0.7, ..., 1.3, 1.4 or off.
prevents media from being detected by an application as CD-R to defeat the ATIP protection. Hide-CDR settings need a specified DEVICE.
enable / disable Hide-CDR.
on enable Hide-CDR. Defeating ATIP protection.
off disable Hide-CDR.
can lock your media to prevent an accidently opening. It is always a good idea lock the drive. This OPTION needs a specified DEVICE.
enable lock modus. Media can not be removed.
disable lock modus. Media can be removed.
destroys the data on your CD/DVD and makes it unreadable. DEVICE needs to be specified for this command.
WARNING: command destroys your media.
quick destroy only the lead in of CD/DVD media.
full destroy complete CD/DVD media.
Plextor Optimised Writing Error Reduction Control (PoweRec) should detect the optimized writing speed for your media-combination. Higher
recording speeds than recommended can result in increased writing errors. PoweRec should prevent you from these errors. DEVICE needs to be
specified for this command.
enable / disable PoweRec.
on enable PoweRec. enabled by default.
off disable PoweRec.
Creates a password protected CD-R. To access a password protected CD-R, it is necessary to enter the correct password and to specify the
--nosecurec disable SecuRec.
enable SecuRec and use a given password. <passwd>
must have at least four, but not more than ten characters.
Allows some speed finetuning on your drives. Lower values result in more silence. You can specify read speed and tray loading speed. DEVICE
must be specified for this command. All settings will be active after reboot. ;-) pxfw /dev/hdX -r
enable / disable SilentMode
on enables SilentMode. This will give you access to
further speed and read settings. Default is on.
off disables SilentMode.
set access time to slow or fast. This has only an affect in combination with CD/DVD speed setting.
fast enables fast access mode. Use with speed setting.
slow enables slow access mode. Use with speed setting.
set maximum read speed for CDs. Default is 32x.
Select speed value from 4, 8, 24, 32, 40, 48.
set maximum write speed for CDs. Default is 32x.
Select speed value from 4, 8, 16, 32, 48.
set maximum read speed for DVDs. Default is 12x.
Select speed value from 2, 5, 8, 12, 16.
set tray eject speed. Default is 0.
Select speed value from 0, 1, ..., 80.
set tray load speed. Default is 63.
Select speed value from 0, 1, ... , 80.
--sm-nosave do not save SilentMode settings
shows only the first session of the CD. You have to enable this feature before you insert the media. This is a useful option for copy pro-
tected audio discs. DEVICE must be specified for this command.
enable / disable SingleSession. Default is off.
on enable SingleSession mode for CD.
off disable SingleSession mode for CD.
allows DVD+R writing simulation. DEVICE must be specified for this command.
mode enable / disable DVD+R writing simulation on enable DVD+R writing simulation mode
off disable DVD+R writing simulation mode
allows increasing the read speed. This deactivates the so called Rip Lock for Video-DVDs. You can also deativate this feature by keeping
the open button of your empty DVD drive pressed for three seconds. SpeedRead can increase vibrations and read errors. DEVICE must be speci-
fied for this command.
enable / disable SpeedRead
on enable SpeedRead. Disable Rip Lock.
off disable SpeedRead. Set Rip Lock.
allows some laser power calibration in a range from -4 to +4. The recording speed is limited to 4x or 8x on CD-R media and to 2x, 2.4x or
4x on DVD media. The recording strategy can also be changed relying on the used media dye. The writing strategies are determining and docu-
menting your own strategies. You would determine the differences by selecting a stretegy and doimg a writing test. VariRec settings per-
sist after a reboot. DEVICE must be specified for this command. Use cdrdao or cdrskin for writing media with VariRec function. Otherwise
if you use cdrecord, your values are flushed.
set VariRec power for CD writing or set it to off.
Select value -4, -3, -2, -1, 0, +2, +2, +3, +4
select writing strategy for CDs depending
on the used dye (Azo, Cyanine, PhtaloCyanine):
select: default, azo, cya, pha, phb, phc, phd
set VariRec power value for DVD writing or set it to off.
Select value -4, -3, -2, -1, 0, +2, +2, +3, +4
select a predefined DVD writing strategy.
select value 0, 1, 2, 3, 4, 5, 6, 7
Pioneer QuietMode feature.
turns on/off read speed limit by 24X for CD and 8X for DVD
sets Pioneer performance profile
available values: quiet, perf, std
quiet turn drive into silent mode
perf turn drive into performance ptomized mode
std reset drive to standard mode
don't make Pioquiet setting permanent
list all available optical devices.
cdvdcontrol -d /dev/hdc --supported
show features that are supported by drive hdc.
cdvdcontrol -d /dev/hda --as-create q a
create a new ASDB entry for device hda and the
inserted DVD media. Strategy is created quickly
and appended to the already existing ASDB list.
cdvdcontrol -d /dev/sr2 --gigarec 0.9
prepare CD for GigaRec 0.9 recording. Use cdrskin
or cdrdao/k3b for writing process.
please report man page improvements to T.Maguin@web.de
Gennady ShultZ Kozlov 04. May, 2009 cdvdcontrol(1)