Z8530_SYNC_DMA_OPEN(9) Public Functions Provided Z8530_SYNC_DMA_OPEN(9)NAME
z8530_sync_dma_open - Open a Z8530 for DMA I/O
int z8530_sync_dma_open(struct net_device * dev, struct z8530_channel * c);
The network device to attach
The Z8530 channel to configure in sync DMA mode.
Set up a Z85x30 device for synchronous DMA in both directions. Two ISA DMA channels must be available for this to work. We assume ISA DMA
driven I/O and PC limits on access.
Alan Cox <email@example.com>
COPYRIGHT Kernel Hackers Manual 3.10 June 2014 Z8530_SYNC_DMA_OPEN(9)
Check Out this Related Man Page
CMDIDE(4) BSD Kernel Interfaces Manual CMDIDE(4)NAME
cmdide -- CMD Technology and Silicon Image IDE disk controllers driver
cmdide* at pci? dev ? function ? flags 0x0000
The cmdide driver supports the CMD Technology PCI0640, PCI0643, PCI0646, PCI0648, PCI0649, and Silicon Image 0680 IDE controllers, and pro-
vides the interface with the hardware for the ata(4) driver.
The 0x0002 flag forces the cmdide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)BUGS
There's no way to reliably know if a PCI064x controller is enabled or not. If the driver finds a PCI064x, it will assume it is enabled
unless the PCIIDE_CMD064x_DISABLE option is specified in the kernel config file. This will be a problem only if the controller has been dis-
abled in the BIOS and another controller has been installed and uses the ISA legacy I/O ports and interrupts.
The PCI0646U controller is known to be buggy with Ultra-DMA transfers, so Ultra-DMA is disabled by default for this controller. To enable
Ultra-DMA, use the PCIIDE_CMD0646U_ENABLEUDMA option. Ultra-DMA can eventually be disabled on a per-drive basis with config flags, see
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD December 13, 2003 BSD
I know the following questions are noobish questions but I am asking them because I am confused about the basics of history behind UNIX and LINUX.
Ok onto business, my questions are-:
Was/Is UNIX ever an open source operating system ?
If UNIX was... (21 Replies)
Hello and thanks in advance for any help anyone can offer me
I'm trying to learn the find command and thought I was understanding it... Apparently I was wrong. I was doing compound searches and I started getting weird results with the -size test. I was trying to do a search on a 1G file owned by... (14 Replies)
i have installed quota on my centos 7 machine and its what im after (setting size limit on users, so they cant fill the hard drive)
i want to now make this part of my create user script for my sftp server so i want to do a echo and a read command so i capture the limit they enter... (0 Replies)
I need to write a shell script which opens a file and increments the version(text) within the file every time the script runs. For example:
$ cat docker_file.yml
So, I would like... (6 Replies)
We use DB2 v10.5 and using DBArtisan tool
Can someone please guide how to convert digits to binary numbers using db2 feature.
Ex> for number 9 , binary should be 1001 ( 8+1)
Any help appreciated. Thanks (2 Replies)
how to using tar with exclude directory and compress it using tar.Z
i only know how to exclude dir only with this command below:
tar -cvf /varios/restore/test.tar -X excludefile.txt /jfma/test1/
how to compress it using 1 command?
Please use CODE tags as... (6 Replies)
Quite an obscure question I think.
We have a rebuild process for remote sites that allows us to PXE rebuild a till (actually a PC with a touch screen and various fancy bits) running CentOS. The current CentOS5 tills work just fine with a tar image restore and some personalisation. Sadly,... (4 Replies)
I had recently learnt a bit of Docker(which provides containerization process).
Here are some of my learning points from it.
Let us start first with very basic question:
What is Docker:
Docker is a platform for sysadmins and developers to DEPLOY, DEVELOP and RUN applications ... (7 Replies)
What is the point of this? Whenever I close my shell it appends to the history file without adding this. I have never seen it overwrite my history file.
# When the shell exits, append to the history file instead of overwriting it
shopt -s histappend (3 Replies)
Hello... And thanks in advance for any help anyone can offer me
I was trying to work out the differences between displaying modify, access, and change times with the 'ls' command. Everything seems in order when I look at files, but the access time on a directory doesn't seem to change when I... (4 Replies)
I am having an issue here with CentOS release 6.6 (Final) that shows all of the space used up, but I can't tell where the space went.
Seemingly I am using up 100%, according to
Filesystem Size Used Avail Use% Mounted on... (27 Replies)
I'm trying to use a bash script for a psych experiment that involves listening to sound files and responding. If I have something like the code below, how can I make sure that a key press is assigned to RESPONSE only after the second echo statement?
for i in 1 2 3; do
... (10 Replies)
After the success of the jq - tool for parsing and manipulating JSON-Data someone wrote a tool called yq, which aims to be the same for YAML, what jq is for JSON. Seems to work fine. I'll definitely give it a chance in future.
... (1 Reply)
I am very pleased to announce that Dave Munro (gull04) is joining the Moderation Team, after being a very valuable member of UNIX.com for 15+ years.
Dave is an IT Consultant with 30 years of experience this year, has worked in many of the industry vertical market segments and has... (6 Replies)