Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

cfsetispeed(3p) [centos man page]

CFSETISPEED(3P) 					     POSIX Programmer's Manual						   CFSETISPEED(3P)

PROLOG
This manual page is part of the POSIX Programmer's Manual. The Linux implementation of this interface may differ (consult the correspond- ing Linux manual page for details of Linux behavior), or the interface may not be implemented on Linux. NAME
cfsetispeed - set input baud rate SYNOPSIS
#include <termios.h> int cfsetispeed(struct termios *termios_p, speed_t speed); DESCRIPTION
The cfsetispeed() function shall set the input baud rate stored in the structure pointed to by termios_p to speed. There shall be no effect on the baud rates set in the hardware until a subsequent successful call to tcsetattr() with the same termios structure. Similarly, errors resulting from attempts to set baud rates not supported by the terminal device need not be detected until the tcsetattr() function is called. RETURN VALUE
Upon successful completion, cfsetispeed() shall return 0; otherwise, -1 shall be returned, and errno may be set to indicate the error. ERRORS
The cfsetispeed() function may fail if: EINVAL The speed value is not a valid baud rate. EINVAL The value of speed is outside the range of possible speed values as specified in <termios.h>. The following sections are informative. EXAMPLES
None. APPLICATION USAGE
None. RATIONALE
Refer to cfgetispeed(). FUTURE DIRECTIONS
None. SEE ALSO
cfgetispeed(), cfgetospeed(), cfsetospeed(), tcsetattr(), the Base Definitions volume of IEEE Std 1003.1-2001, Chapter 11, General Terminal Interface, <termios.h> COPYRIGHT
Portions of this text are reprinted and reproduced in electronic form from IEEE Std 1003.1, 2003 Edition, Standard for Information Technol- ogy -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2003 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between this version and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html . IEEE
/The Open Group 2003 CFSETISPEED(3P)

Check Out this Related Man Page

CFGETISPEED(3P) 					     POSIX Programmer's Manual						   CFGETISPEED(3P)

PROLOG
This manual page is part of the POSIX Programmer's Manual. The Linux implementation of this interface may differ (consult the correspond- ing Linux manual page for details of Linux behavior), or the interface may not be implemented on Linux. NAME
cfgetispeed - get input baud rate SYNOPSIS
#include <termios.h> speed_t cfgetispeed(const struct termios *termios_p); DESCRIPTION
The cfgetispeed() function shall extract the input baud rate from the termios structure to which the termios_p argument points. This function shall return exactly the value in the termios data structure, without interpretation. RETURN VALUE
Upon successful completion, cfgetispeed() shall return a value of type speed_t representing the input baud rate. ERRORS
No errors are defined. The following sections are informative. EXAMPLES
None. APPLICATION USAGE
None. RATIONALE
The term "baud" is used historically here, but is not technically correct. This is properly "bits per second", which may not be the same as baud. However, the term is used because of the historical usage and understanding. The cfgetospeed(), cfgetispeed(), cfsetospeed(), and cfsetispeed() functions do not take arguments as numbers, but rather as symbolic names. There are two reasons for this: 1. Historically, numbers were not used because of the way the rate was stored in the data structure. This is retained even though a func- tion is now used. 2. More importantly, only a limited set of possible rates is at all portable, and this constrains the application to that set. There is nothing to prevent an implementation accepting as an extension a number (such as 126), and since the encoding of the Bxxx symbols is not specified, this can be done to avoid introducing ambiguity. Setting the input baud rate to zero was a mechanism to allow for split baud rates. Clarifications in this volume of IEEE Std 1003.1-2001 have made it possible to determine whether split rates are supported and to support them without having to treat zero as a special case. Since this functionality is also confusing, it has been declared obsolescent. The 0 argument referred to is the literal constant 0, not the symbolic constant B0. This volume of IEEE Std 1003.1-2001 does not preclude B0 from being defined as the value 0; in fact, implementations would likely benefit from the two being equivalent. This volume of IEEE Std 1003.1-2001 does not fully specify whether the previous cfsetispeed() value is retained after a tcgetattr() as the actual value or as zero. Therefore, conforming applications should always set both the input speed and output speed when setting either. In historical implementations, the baud rate information is traditionally kept in c_cflag. Applications should be written to presume that this might be the case (and thus not blindly copy c_cflag), but not to rely on it in case it is in some other field of the structure. Set- ting the c_cflag field absolutely after setting a baud rate is a non-portable action because of this. In general, the unused parts of the flag fields might be used by the implementation and should not be blindly copied from the descriptions of one terminal device to another. FUTURE DIRECTIONS
None. SEE ALSO
cfgetospeed(), cfsetispeed(), cfsetospeed(), tcgetattr(), the Base Definitions volume of IEEE Std 1003.1-2001, Chapter 11, General Terminal Interface, <termios.h> COPYRIGHT
Portions of this text are reprinted and reproduced in electronic form from IEEE Std 1003.1, 2003 Edition, Standard for Information Technol- ogy -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2003 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between this version and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html . IEEE
/The Open Group 2003 CFGETISPEED(3P)
Man Page

Featured Tech Videos