Linux and UNIX Man Pages

Linux & Unix Commands - Search Man Pages

usb_modeswitch_dispatcher(1) [centos man page]

USB_MODESWITCH_DISPATCHER(1)				      General Commands Manual				      USB_MODESWITCH_DISPATCHER(1)

NAME
usb_modeswitch_dispatcher - dispatcher not intended for direct invocation. SYNOPSIS
usb_modeswitch_dispatcher DESCRIPTION
usb_modeswitch_dispatcher is doing additional device checking and using the usb_modeswitch binary to switch with the selected device config file. If no drivers are taking care of the device after the mode switch, the dispatcher will try to load and bind the "option" serial driver, in order to make the device usable. This program is called by udev and is not supposed to be called directly by the user. SEE ALSO
usb_modeswitch(1). USB_MODESWITCH_DISPATCHER(1)

Check Out this Related Man Page

USB_MODESWITCH(1)					      General Commands Manual						 USB_MODESWITCH(1)

NAME
usb_modeswitch - switch mode of "multi-state" USB devices SYNOPSIS
usb_modeswitch [-heWQDIvpVPmM23rwdHSOBGTNALnsRiuagft] [-c filename] DESCRIPTION
Several new USB devices have their proprietary Windows drivers onboard, most of them WAN dongles. When plugged in for the first time, they act like a flash storage and start installing the Windows driver from there. If the driver is already installed, it makes the storage device disappear and a new device, mainly composite with modem ports, shows up. On Linux, in most cases the drivers are available as kernel modules, such as "usbserial" or "option". However, the device shows up as "usb- storage" by default. usb_modeswitch can send a provided bulk message (most likely a mass storage command) to the device which is known to initiate the mode switching. In some cases, USB control commands are used for switching. These cases are handled by custom functions, and no bulk message needs to be provided. Usually, the program is distributed with a set of configurations for many known devices, which in combination with a wrapper script launched from the udev daemon allows a fully automatic handling of a device upon insertion. OPTIONS
This program follows the usual GNU command line syntax, with long options starting with two dashes ('--'). A summary of options is included below. -h --help Show summary of options. -e --version Print version information and exit -v --default-vendor NUM Vendor ID to look for (mandatory), usually given as hex number (example: 0x12d1). Each USB device is identified by a number officialy assigned to the vendor by the USB association and a number for the respective model (product ID) chosen by the vendor -p --default-product NUM Product ID to look for (mandatory) -V --target-vendor NUM Target vendor ID. When given will be searched for and detected initially for information purposes. If success checking (option -s) is active, providing target IDs (vendor/product) or target class is recommended -P --target-product NUM Target product ID -b --busnum NUM -g --devnum NUM If bus and device number are provided, the handling of a specific device on a specific USB port is guaranteed, in contrast to using only the USB ID. This is important if there are multiple similar devices on a system -C --target-class NUM Target Device Class according to the USB specification. Some devices keep their original vendor/product ID after successful switching. To prevent them from being treated again, the device class can be checked. For unswitched devices it is always 8 (storage class), for switched modems it is often 0xff (vendor specific). In composite modes, the class of the first interface is watched -m --message-endpoint NUM A specific endpoint to use for data transfers. Only for testing purposes; usually endpoints are determined from the device attributes -M --message-content STRING A bulk message to send as a switching command. Provided as a hexadecimal string -2, -3 --message-content2, --message-content3 STRING Additional bulk messages to send as switching commands. Provided as hexadecimal strings. When used with mass storage commands, setting --need-response is strongly advised to comply with specifications and to avoid likely errors -w --release-delay NUM After issuing all bulk messages, wait for NUM milliseconds before releasing the interface. Required for some modems on older systems (especially after an EJECT message) -n --need-response Read the response (command status wrapper) to a mass storage command transfer. Some devices have trouble switching if the response is not read; most are disappearing right away. When sending multiple mass storage commands with -2 and -3, this may need to be set to avoid transfer errors -r --response-endpoint NUM Try to read the response to a storage command from there if option -n is active. Only for testing purposes; usually endpoints are determined from the device attributes -d --detach-only Just detach the current driver. This is sufficient for some early devices to switch successfully. Otherwise this feature can be used as a 'scalpel' for special cases, like separating the driver from individual interfaces -H --huawei-mode Send a special control message used by older Huawei devices -S --sierra-mode Send a special control message used by Sierra devices -G --gct-mode Send a special control message used by GCT chipsets -T --kobil-mode Send a special control message used by Kobil devices -T --sequans-mode Send a special control message used by Sequans chipset -T --mobileaction-mode Send a special control message used by the MobileAction device -B --qisda-mode Send a special control message used by Qisda devices -O --sony-mode Apply a special sequence used by Sony Ericsson devices. Implies option --success -L --cisco-mode Send a sequence of bulk messages used by Cisco devices -R --reset-usb Send a USB reset command to the device. Can be combined with any switching method or stand alone. It is always done as the last step of all device interactions. Few devices need it to complete the switching; apart from that it may be useful during testing -c --config FILENAME Use a specific config file. If any ID or switching options are given as command line parameters, this option is ignored. In that case all mandatory parameters have to be provided on the command line -f --long-config STRING Provide device details in config file syntax as a multiline string on the command line -t --stdinput Read the device details in config file syntax from standard input, e.g. redirected from a command pipe (multiline text) -Q --quiet Don't show progress or error messages -W --verbose Print all settings before running and show libusb debug messages -D --sysmode Changes the behaviour of the program slightly. A success message including the effective target device ID is put out and a syslog notice is issued. Mainly for integration with a wrapper script -s --success NUM After switching, keep checking for the result up to max. NUM seconds. If target IDs or target class were provided, their appear- ance indicates certain success. Otherwise the disconnection of the original device is rated as likely proof -I --no-inquire do not obtain SCSI attributes from device (default is on). For proper identification of differing devices the attributes of the storage part provide valuable information. This is not needed for devices that are known and supported -i --interface NUM Select initial USB interface (default: 0). Only for testing purposes -u --configuration NUM Select USB configuration (applied after any other possible switching actions) -a --altsetting NUM Select alternative USB interface setting (applied after switching). Mainly for testing AUTHOR
This manual page was originally written by Didier Raboud (didier@raboud.com) for the Debian system. Additions made by Josua Dietze. Permis- sion is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 or any later version published by the Free Software Foundation. The complete text of the current GNU General Public License can be found in http://www.gnu.org/licenses/gpl.txt USB_MODESWITCH(1)
Man Page