css(4) [bsd man page]

CSS(4)							     Kernel Interfaces Manual							    CSS(4)

NAME

       css - DEC IMP-11A LH/DH IMP interface

SYNOPSIS

       /sys/conf/SYSTEM:
	    NCSS css_controllers     # DEC/CSS IMP11-A ARPAnet IMP interface

DESCRIPTION

       The  css device provides a Local Host/Distant Host interface to an IMP.	It is normally used when participating in the DARPA Internet.  The
       controller itself is not accessible to users, but instead provides the hardware support to the IMP interface  described	in  imp(4).   When
       configuring, the imp(NIMP) pseudo-device is also included.

DIAGNOSTICS

       css%d:  not  alive.  The initialization routine was entered even though the device did not autoconfigure.  This is indicates a system prob-
       lem.

       css%d: can't initialize.  Insufficient UNIBUS resources existed to initialize the device.  This is likely to occur when the device  is  run
       on  a buffered data path on an 11/750 and other network interfaces are also configured to use buffered data paths, or when it is configured
       to use buffered data paths on an 11/730 (which has none).

       css%d: imp doesn't respond, icsr=%b.  The driver attempted to initialize the device, but the IMP failed to respond after 500 tries.   Check
       the cabling.

       css%d: stray output interrupt csr=%b.  An interrupt occurred when no output had previously been started.

       css%d: output error, ocsr=%b icsr=%b.  The device indicated a problem sending data on output.

       css%d: recv error, csr=%b.  The device indicated a problem receiving data on input.

       css%d: bad length=%d.  An input operation resulted in a data transfer of less than 0 or more than 1008 bytes of data into memory (according
       to the word count register).  This should never happen as the maximum size of a host-IMP message is 1008 bytes.

3rd Berkeley Distribution					  August 20, 1987							    CSS(4)

ACC(4)							     Kernel Interfaces Manual							    ACC(4)

NAME

       acc - ACC LH/DH IMP interface

SYNOPSIS

       /sys/conf/SYSTEM:
	    NACC 0    # ACC LH/DH ARPAnet IMP interface
	    PLI  YES  # LH/DH is connected to a PLI

DESCRIPTION

       The  acc device provides a Local Host/Distant Host interface to an IMP.	It is normally used when participating in the DARPA Internet.  The
       controller itself is not accessible to users, but instead provides the hardware support to the IMP interface  described	in  imp(4).   When
       configuring, the imp(NIMP) pseudo-device must also be included.

DIAGNOSTICS

       acc%d: not alive.  The initialization routine was entered even though the device did not autoconfigure.	This indicates a system problem.

       acc%d:  can't  initialize.  Insufficient UNIBUS resources existed to initialize the device.  This is likely to occur when the device is run
       on a buffered data path on an 11/750 and other network interfaces are also configured to use buffered data paths, or when it is	configured
       to use buffered data paths on an 11/730 (which has none).

       acc%d:  imp doesn't respond, icsr=%b.  The driver attempted to initialize the device, but the IMP failed to respond after 500 tries.  Check
       the cabling.

       acc%d: stray xmit interrupt, csr=%b.  An interrupt occurred when no output had previously been started.

       acc%d: output error, ocsr=%b, icsr=%b.  The device indicated a problem sending data on output.

       acc%d: input error, csr=%b.  The device indicated a problem receiving data on input.

       acc%d: bad length=%d.  An input operation resulted in a data transfer of less than 0 or more than 1008 bytes of data into memory (according
       to the word count register).  This should never happen as the maximum size of a host-IMP message is 1008 bytes.

3rd Berkeley Distribution					   July 26, 1987							    ACC(4)