RPIECE(1) General Commands Manual RPIECE(1)
NAME
rpiece - render pieces of a RADIANCE picture
SYNOPSIS
rpiece [ -v ][ -x xres ][ -y yres ][ -X xdiv ][ -Y ydiv ][ -F|R syncfile ][ -T timelim ] [ $EVAR ] [ @file ] [ rpict options ] -o picture
octree
DESCRIPTION
Rpiece renders a RADIANCE picture a piece at a time, calling rpict(1) to do the actual work. This is useful for running multiple rpict
processes on cooperating machines to render a single picture, which is a shared file specified with the -o option. The overall picture
dimensions will be xres by yres (or smaller, depending on the -pa option and other view options), and the picture will be rendered in xdiv
by ydiv pieces.
There are two basic methods for telling rpiece which piece(s) of a picture to render. The explicit method is to write on the standard
input the X and Y position of the desired piece(s), where X runs from zero to xdiv-1 and Y runs from zero to ydiv-1. (The lower left piece
of a picture corresponds to (0,0) in this system.) Alternatively, the implicit specification method uses a synchronization file to deter-
mine which piece is to be rendered next. Specified with the -F option, syncfile initially contains the values for xdiv and ydiv, so the -X
and -Y options are unnecessary. (However, they are used if syncfile does not exist.) The first rpiece process puts a lock on syncfile and
modifies its contents before starting work on the first piece of the image. It writes the X and Y position of the piece it will work on,
so the next rpiece process to modify syncfile will start on the next piece. (When it finishes with its piece, it appends the index to the
end of syncfile.) This procedure continues until all the pieces are done, at which point all of the rpiece processes will terminate.
The -R option may be used instead of -F if some of the pieces were not properly finished by previous (killed) runs of rpiece. This option
should be used by at most one rpiece process, which must be started first and with no other rpiece processes running or else it will reren-
der the same pieces other processes have begun. Once the recover process is started, you may start other rpiece processes using the -F
option to run simultaneously. If some processes die during execution, leaving one or more half-finished pieces in the picture even though
the other processes think the work is done, you may run a single rpiece with the -R option by itself to repair the holes.
The -v flag switches on verbose mode, where rpiece reports to the standard output after each piece begins and after each piece is finished.
Options may be given on the command line and/or read from the environment and/or read from a file. A command argument beginning with a
dollar sign ('$') is immediately replaced by the contents of the given environment variable. A command argument beginning with an at sign
('@') is immediately replaced by the contents of the given file.
EXAMPLE
First rpiece process is started on the machine "goober":
goober% echo 1 8 > syncfile
goober% echo -F syncfile -x 1024 -y 1024 -vf view -o picture octree > args
goober% rpiece @args &
Second rpiece processes is started on the machine "sucker":
sucker% rpiece @args &
NOTES
Due to NFS file buffering, the network lock manager is employed to guarantee consistency in the output file even though non-overlapping
writes are used. This would tend to slow the process down if rpiece were to wait for this I/O to complete before starting on the next
piece, so rpiece forks separate processes to hang around waiting for I/O completion. The number of processes thus designated is set by the
MAXFORK macro in the program (compiled in the src/util directory). If the fork call is slow on a system, it may actually be better to set
MAXFORK to zero. In other cases, the network lock manager may be so slow that this value should be increased to get the best utilization.
The output picture is not run-length encoded, and can be quite large. The approximate size (in kilobytes) can be computed by the simple
formula:
filesize = xres*yres/256
Make sure that there is enough space on the filesystem to hold the entire picture before beginning. Once the picture is finished, the
ra_rgbe(1) program with the -r option may be used to convert to a run-length encoded picture for more efficient storage, although pfilt(1)
or any of the other Radiance picture filters will do the same thing.
The ALRM signal may be used to gracefully terminate an rpiece process after it finishes the current piece. This permits other currently
running or subsequently started rpiece process(es) to continue rendering the picture without loss. The -T option will send the ALRM signal
to rpiece after the specified number of (decimal) hours. This is the best way to force a time limit on the computation, since information
will not be lost, though the process may continue for some time afterwards to finish its current piece.
BUGS
This program may not work on some systems whose NFS lock manager is unreliable. In particular, some System V derivative UNIX systems often
have problems with the network lock manager. If the output is scrambled or rpict aborts with some ambient file related problem, you should
just remove the ambient file and go back to normal rendering.
AUTHOR
Greg Ward
SEE ALSO
getinfo(1), pfilt(1), ra_rgbe(1), rpict(1), ximage(1)
RADIANCE
10/1/98 RPIECE(1)