GMIRROR(8) BSD System Manager's Manual GMIRROR(8)
NAME
gmirror -- control utility for mirrored devices
SYNOPSIS
gmirror label [-Fhnv] [-b balance] [-s slice] name prov ...
gmirror clear [-v] prov ...
gmirror configure [-adfFhnv] [-b balance] [-s slice] name
gmirror configure [-v] -p priority name prov
gmirror rebuild [-v] name prov ...
gmirror resize [-v] [-s size] name
gmirror insert [-hiv] [-p priority] name prov ...
gmirror remove [-v] name prov ...
gmirror activate [-v] name prov ...
gmirror deactivate [-v] name prov ...
gmirror destroy [-fv] name ...
gmirror forget [-v] name ...
gmirror stop [-fv] name ...
gmirror dump prov ...
gmirror list
gmirror status
gmirror load
gmirror unload
DESCRIPTION
The gmirror utility is used for mirror (RAID1) configurations. After a mirror's creation, all components are detected and configured auto-
matically. All operations like failure detection, stale component detection, rebuild of stale components, etc. are also done automatically.
The gmirror utility uses on-disk metadata (stored in the provider's last sector) to store all needed information. Since the last sector is
used for this purpose, it is possible to place a root file system on a mirror.
The first argument to gmirror indicates an action to be performed:
label Create a mirror. The order of components is important, because a component's priority is based on its position (starting from 0
to 255). The component with the biggest priority is used by the prefer balance algorithm and is also used as a master component
when resynchronization is needed, e.g. after a power failure when the device was open for writing.
Additional options include:
-b balance Specifies balance algorithm to use, one of:
load Read from the component with the lowest load. This is the default balance algorithm.
prefer Read from the component with the biggest priority.
round-robin Use round-robin algorithm when choosing component to read.
split Split read requests, which are bigger than or equal to slice size on N pieces, where N is the number of
active components.
-F Do not synchronize after a power failure or system crash. Assumes device is in consistent state.
-h Hardcode providers' names in metadata.
-n Turn off autosynchronization of stale components.
-s slice When using the split balance algorithm and an I/O READ request is bigger than or equal to this value, the I/O request
will be split into N pieces, where N is the number of active components. Defaults to 4096 bytes.
clear Clear metadata on the given providers.
configure Configure the given device.
Additional options include:
-a Turn on autosynchronization of stale components.
-b balance Specifies balance algorithm to use.
-d Do not hardcode providers' names in metadata.
-f Synchronize device after a power failure or system crash.
-F Do not synchronize after a power failure or system crash. Assumes device is in consistent state.
-h Hardcode providers' names in metadata.
-n Turn off autosynchronization of stale components.
-p priority Specifies priority for the given component prov.
-s slice Specifies slice size for split balance algorithm.
rebuild Rebuild the given mirror components forcibly. If autosynchronization was not turned off for the given device, this command
should be unnecessary.
resize Change the size of the given mirror.
Additional options include:
-s size New size of the mirror is expressed in logical block numbers. This option can be omitted, then it will be automatically
calculated to maximum available size.
insert Add the given component(s) to the existing mirror.
Additional options include:
-h Hardcode providers' names in metadata.
-i Mark component(s) as inactive immediately after insertion.
-p priority Specifies priority of the given component(s).
remove Remove the given component(s) from the mirror and clear metadata on it.
activate Activate the given component(s), which were marked as inactive before.
deactivate Mark the given component(s) as inactive, so it will not be automatically connected to the mirror.
destroy Stop the given mirror and clear metadata on all its components.
Additional options include:
-f Stop the given mirror even if it is opened.
forget Forget about components which are not connected. This command is useful when a disk has failed and cannot be reconnected, pre-
venting the remove command from being used to remove it.
stop Stop the given mirror.
Additional options include:
-f Stop the given mirror even if it is opened.
dump Dump metadata stored on the given providers.
list See geom(8).
status See geom(8).
load See geom(8).
unload See geom(8).
Additional options include:
-v Be more verbose.
EXIT STATUS
Exit status is 0 on success, and 1 if the command fails.
EXAMPLES
Use 3 disks to setup a mirror. Choose split balance algorithm, split only requests which are bigger than or equal to 2kB. Create file sys-
tem, mount it, then unmount it and stop device:
gmirror label -v -b split -s 2048 data da0 da1 da2
newfs /dev/mirror/data
mount /dev/mirror/data /mnt
...
umount /mnt
gmirror stop data
gmirror unload
Create a mirror on disk with valid data (note that the last sector of the disk will be overwritten). Add another disk to this mirror, so it
will be synchronized with existing disk:
gmirror label -v -b round-robin data da0
gmirror insert data da1
Create a mirror, but do not use automatic synchronization feature. Add another disk and rebuild it:
gmirror label -v -n -b load data da0 da1
gmirror insert data da2
gmirror rebuild data da2
One disk failed. Replace it with a brand new one:
gmirror forget data
gmirror insert data da1
Create a mirror, deactivate one component, do the backup and connect it again. It will not be resynchronized, if there is no need to do so
(there were no writes in the meantime):
gmirror label data da0 da1
gmirror deactivate data da1
dd if=/dev/da1 of=/backup/data.img bs=1m
gmirror activate data da1
NOTES
Doing kernel dumps to gmirror providers is possible, but some conditions have to be met. First of all, a kernel dump will go only to one
component and gmirror always chooses the component with the highest priority. Reading a dump from the mirror on boot will only work if the
prefer balance algorithm is used (that way gmirror will read only from the component with the highest priority). If you use a different bal-
ance algorithm, you should add:
gmirror configure -b prefer data
to the /etc/rc.early script and:
gmirror configure -b round-robin data
to the /etc/rc.local script. The decision which component to choose for dumping is made when dumpon(8) is called. If on the next boot a
component with a higher priority will be available, the prefer algorithm will choose to read from it and savecore(8) will find nothing. If
on the next boot a component with the highest priority will be synchronized, the prefer balance algorithm will read from the next one, thus
will find nothing there.
SEE ALSO
geom(4), dumpon(8), geom(8), gvinum(8), mount(8), newfs(8), savecore(8), umount(8)
HISTORY
The gmirror utility appeared in FreeBSD 5.3.
AUTHORS
Pawel Jakub Dawidek <pjd@FreeBSD.org>
BUGS
There should be a way to change a component's priority inside a running mirror.
There should be a section with an implementation description.
Documentation for sysctls kern.geom.mirror.* is missing.
BSD
December 27, 2013 BSD